Maintenance And Care; Spare Parts And Accessories - Flex CSE 55 T Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 31
CSE 55 T
 Feed the saw evenly through the material.
 After cutting:
– Switch off the saw. Saw blade continues
running briefly!
– When the saw is lifted, the saw blade
returns to the initial position and the
guard is locked.
 At the end of work:
Thoroughly clean the electric power tool
and accessories.
klqb
qç=éêçÅÉëë=ä~êÖÉ=ïçêâéáÉÅÉë=çê=íç=Åìí=ëíê~áÖÜí=
ÉÇÖÉëI=óçì=Å~å=~äëç=~íí~ÅÜ=~=Ä~ê=çê=ëáãáä~ê=
áãéäÉãÉåí=íç=íÜÉ=ïçêâéáÉÅÉ=~åÇ=ÖìáÇÉ=íÜÉ=
ÅáêÅìä~ê=ë~ï=ïáíÜ=íÜÉ=ë~ï=ÄÉåÅÜ=~äçåÖ=íÜáë=
~ìñáäá~êó=ëíçéK=
Plunge cuts
`^rqflk>
Ó cçê=éäìåÖÉ=Åìíë=íÜÉ=ãáíêÉ=~åÖäÉ=ãìëí=
ÄÉ ëÉí=íç=MøK
Ó q~âÉ=ëìáí~ÄäÉ=éêÉÅ~ìíáçåë=íç=éêÉîÉåí=
~ âáÅâÄ~ÅâI=ÉKÖK=Ñáñ=~=ïççÇÉå=ÄäçÅâ=
çå=íÜÉ=ïçêâéáÉÅÉ=ÄÉÜáåÇ=íÜÉ=ã~ÅÜáåÉK
The sequence for making plunge cuts can be
found in the section "Sawing along a scribe
mark". The mitre angle must be 0°.
To improve orientation when making plunge
cuts, marks are attached to the inspection
window and the guard (see diagram).
These marks identify the cut area of the fully
plunged saw blade (at maximum cutting
depth).

Maintenance and care

t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=ÉäÉÅíêáÅ=
éçïÉê=íççäI=éìää=çìí=íÜÉ=ã~áåë=éäìÖK=
Cleaning the electric power tool
t^okfkd>
aç=åçí=ìëÉ=ï~íÉê=çê=äáèìáÇ=ÇÉíÉêÖÉåíëK
 Regularly blow out the housing interior
and motor with dry compressed air.
 Clean saw bench and setting devices
using a vacuum cleaner and paint brush.
 Occasionally spray joints with machine oil.
 Also clean the guide rail, otherwise the
saw will not be guided properly resulting
in an inaccurate cut.
Repairs
Repairs may be carried out by an authorised
customer service centre only.
klqb
aìêáåÖ=íÜÉ=ï~êê~åíó=éÉêáçÇ=Çç=åçí=äççëÉå=
íÜÉ ëÅêÉïë=çå=íÜÉ=ãçíçê=ÜçìëáåÖK=
kçåJÅçãéäá~åÅÉ=ïáää=ÇÉÉã=íÜÉ=Öì~ê~åíÉÉ=
çÄäáÖ~íáçåë=çÑ=íÜÉ=ã~åìÑ~ÅíìêÉê=åìää=~åÇ=îçáÇK

Spare parts and accessories

Other accessories, in particular insertion
tools, can be found in the manufacturer's
catalogues.
Exploded drawings and spare-part lists can
be found on our homepage:
www.flex-tools.com
29

Publicité

Table des Matières
loading

Table des Matières