Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EUROPE 205
Advice before Use
•
Read carefully these instructions.
•
As soon as the equipment is delivered, open packings and inspect
the equipment carefully.
If you notice any damage, contact immediately the transport company
and register your complaint in due form with mention of the defects.
Be sure that this equipment left our factory in perfect condition.
•
Check if the received equipment is consistent with the delivery notice
and if this delivery notice is consistent with your order.
If it is not, contact immediately your supplier.
General Remarks
This luminaire is a lighting equipment designed for professional use only
in theatres and indoor television or movie studios.
This luminaire has been designed for being mounted on non-combustible
surfaces (
).
Designed and built in accordance with EN 60950 safety regulations, it
must imperatively be connected to earth by means of its earth wire.
I t
a l s o
c o m p l i e s
w i t h
(598-1/598-2-17 publications).
To prevent any electrical shock, there is no need to open this equipment
when functioning.
Nevertheless:
•
Any part or lenses have to be replaced if they are visibly damaged
and their efficiency might be reduced, for example in case of deep
cracks or scratches.
•
Lamp must be changed if damaged or distorted by heat.
If internal access is needed for control, service or repair purposes,
always refer to qualified personnel.
In all events, always unplug the power supply cable before opening,
lethal voltage present inside
It is the user's responsibility to use the luminaire for its intended purpose
and to check the equipment that might be connected to it.
The luminaire can under no circumstances be modified.
ADB will not assume any responsibility in case of damage resulting from
modications made to the luminaire.
This luminaire is a piece of professional equipment designed for easy
and simple use. Nevertheless, always refer to qualified personnel for
any installation or repair work.
Important Remark
Power supply cables and other connections are essential for your
equipment and contribute greatly to a safe and trouble free operation.
•
Always hold the plug when disconnecting a cable, never pull the
cable.
•
Never use cables or connectors in bad condition, check them before
installation and periodically thereafter.
•
Never tie power supply and data cables together.
P a g e
6
Issue 002
t h e
C E I
s a f e t y
r e g u l a t i o n s
www.adbstagelight.com
Beam Shaping Shutters Insertion
Fitting the Lamp
Type of lamp to use
•
GY16 lampholder 2 kW lamp.
•
Light centre lenght (LCL) shall be 70 mm
Unplug luminaire power supply cable.
Open the access door to the lamp and position the lamp carrier
back by means of the fine adjustment knob.
Plug the lamp into the socket (GY16 lampholder), close the door
and connect the power supply cable.
Notes:
•
For optimal lamp performance, please refer to the manufacturer's
notice.
•
The lamp must be changed if damaged or distorted by heat.
Electrical Connection
This luminaire is designed for operating at a nominal voltage of
230 V.
It is delivered with a cable H05SS-F T180°C 3 x 1,5 mm
In use, take care to move away the cable from the hot parts of the
luminaire.
Use IMPERATIVELY this cable with your luminaire.
For your own safety, make sure the earth wire (yellow-green) is
ALWAYS connected to earth.
Plug the cable into the power supply socket at the back end of the
luminaire. Secure the power plug with the stirrup.
If the cable or the power cord is damaged, it must be replaced with a
specific cable or power cord power cord exclusively provided by the
manufacturer or by an authorized service agent.
Photobiological Safety Assesment: Group 2
Ethr: 2473,8 Lux
IMax: 946 000 Cd
DThr: 19,6 m
Luminaires should be positioned so that prolonged staring into luminaire
at a distance closer than DThr is not expected.
Insert shutters
as described
opposite, start
with corners
marked with «X»
2
of6 2 m length.
Publicité
Table des Matières
