Globalstar Sat-Fi2 Manuel D'installation

VoIP & POTS INSTALLATION GUIDE
SETUP/CONNECTION INSTRUCTIONS
NOTE: The following steps must be completed in the proper order. DO NOT power on any device until instructed to
do so in the steps below.
Install the Sat-Fi2 Remote Antenna Station (RAS) in
1
accordance with the Sat-Fi2 Remote Antenna Station
Quick Installation Guide and perform the following:
• Power on the RAS - The Power On sequence can
take up to 5 minutes.
• Once the Power and Satellite LEDs are blinking in
unison, proceed to Step 2.
2 Connect an Ethernet Cable to the RAS Ethernet Port.
Connect the other end of the Ethernet Cable to Port 1
3
on the 5-Port Switch.
4 Connect an Ethernet Cable to Port 2 on the 5-Port Switch.
Connect the other end of the Ethernet cable to the
5
Internet Port on the Cisco VoIP Router.
Connect an RJ11 Cable to the Phone 1 Port on the
6
CiscoVoIP Router.
Sat-Fi2 RAS Power LED
SOS SOS
1
2
12VDC
12VDC
POTS Phone
1 2 3
1 2 3
4 5 4 5 6 6
7 7 8 9 8 9
0 0 # #
7
FLASH REDIAL FLASH REDIAL SOS SOS
Connect the other end of the RJ11 Cable to the POTS Phone.
7
8 For the 5-Port Swtich, perform the following:
• Connect the Power Cord into the Power port of the
5-Port Switch.
• Connect the Power Cord to an AC Power source. Wait
30 seconds for power and ethernet connectivity.
9
For the Cisco VoIP Router perform the following:
• Connect the Power Cord into the Power port of the
Cisco VoIP Router.
• Connect the Power Cord to an AC Power source.
• Boot time may take up to 2 minutes.
When the Cisco VoIP Router Phone 1 LED turns to a
10
steady Green, the POTS Phone is operational.
Satellite LED S.O.S. LED
5-Port Switch
SOS SOS
LINKSYS LINKSYS 5-PORT GIGABIT SWTICH 5-PORT GIGABIT SWTICH LINK/ACT/GB LINK/ACT/GB
SE3005 SE3005
SYSTEM SYSTEM
1 1 2 2 3 3 4 4 5
3 4
Power Switch
Phone 1 LED
Cisco VoIP Router
10
RESET RESET PHONE 1 PHONE 1 PHONE 2 PHONE 2 INTERNET INTERNET DC 5V
POWER
6 5
CALLING USING THE POTS PHONE
1 Ensure that both the Sat-Fi2 RAS Power LED and Satellite LED are blinking Green.
2 Lift the Handset of the POTS Phone and check for a dial tone.
3
Dial any US or Canadian cellular, land line using normal 10-digit dialing.
Example: (555) 543-1234
4 There will be a short delay before hearing a ring and a short delay once the call is answered.
5 When finished, hang up and the call is completed.
Note: To make an emergency call, dial 911. This does not initiate S.O.S. mode but will dial directly to GEOS
International Emergency Response Coordination Center (IERCC).
TROUBLESHOOTING
1 On the Sat-Fi2 RAS, perform the following:
• Check if the Power LED and Satellite LED are blinking Green.
• If the Satellite LED is blinking Red, the Sat-Fi2 RAS is waiting to connect. The Sat-Fi2 RAS will connect
automatically.
2 On the 5-Port Switch perform the following:
• Check to see if the Switch is powered on.
• Check the Ethernet connections between the Sat-Fi2 RAS and 5-Port Switch are connected and secure in
5
5-Port Switch
8
accordance with the diagram.
Power Cord
Check the Ethernet connections between the 5-Port Switch and the Cisco VoIP Router are connected and secure in
3
accordance with the diagram.
4 On the Cisco VoIP Router, perform the following:
• Check if the Phone 1 LED is Green.
• If the Phone 1 LED is not Green, perform the following:
¶ Unplug the Power Cord from the Cisco VoIP router and wait 30 seconds.
Cisco VoIP Router
DC 5V
POWER
Power Cord
9
5 Connect the Power Cord to the Cisco VoIP Router and wait for the device to reboot. This may take up to 2 minutes.
6
The Phone 1 LED should be Green and the Sat-Fi2 RAS POTS Phone is operational.