Alarm End Of Life; Ionization And Photoelectric Technology - First Alert Onelink 1042136 Mode D'emploi

Regular Maintenance (Continued)
To Replace Batteries (Continued)
Step 3
Connect new battery to connector ensuring that
release lever engages and insert battery into the
battery compartment.
Step 4
Close the battery compartment, and re-mount the
Alarm if you removed it from the mounting bracket.
Then test the unit by pressing the Test button
If the alarm does not test, check the battery to ensure it is properly connected and the alarm is properlymounted in the bracket.

Alarm End of Life

Permanently Deactivating the Alarm
After 10 years of operation, deactivate the Alarm by following the diagram below: Score
label on dotted line and move switch all the way to the right to DEACTIVATE mode.
NOTE:
At end of life indication (chirp): unit must be put into deactivation mode to deactivate
remaining stored energy in battery. Unit will no longer function once put into this mode.
Unit will resist re-mounting. Once deactivated, replace Alarm immediately.
SINGLE AND/OR MULTIPLE STATION SMOKE & CO ALARM
MODEL NO. 1042136
PHOTOELECTRIC
SMOKE SENSITIVITY: 0.96 – 2.45 %/ft OBSC.
W WARNING!
Carbon monoxide cannot be seen or smelled but can kill you.
If alarm signal sounds: 1. Operate Test/Silence button.
XXX-XX-XXX
2. Call your emergency services. (Fire Dept. or 911)
3. Immediately move to fresh air - outdoors or by an open door/window.
Alarm will not operate if batteries are dead, disconnected or
improperly installed. Refer to user's manual for complete battery IMPORTANT!
W
replacement list, installation, operating and safety information /
instructions. Use only batteries speci ed. Use of other batteries may
CARBON MONOXIDE SENSITIVITY: If CO levels reach
have a detrimental effect on product operations.
70ppm, it must activate within 60-240 minutes. At
MAINTENANCE AND TESTING: 150ppm within 10-50 minutes. At 400ppm within 4-15
Constant use at high or low temperatures or high humidity may reduce minutes. Refer to user's manual for more information.
battery life. Test after installation, weekly, and after cleaning. Gently Contains Transmitter Modules FCC ID:
Follow and Retain User's
vacuum monthly. Never use water, cleaners or solvents.
Manual: BRK Brands, Inc. M7U-BT1IOT and FCC ID: TLZ-CU300
HOW TO ACTIVATE ALARM: 1301 Joe Battle, Contains Transmitter Modules IC:
El Paso, TX 79936. 10190A-BT1IOT and IC: 6100A-CU300
Align alarm with mounting bracket and turn clockwise. Chasing Blue
LED's and Welcome Message indicate alarm is activated. Consumer Affairs:
Replace Alarm 10 Yrs. After Installation
1-833-ONELINK
HOW TO DEACTIVATE ALARM:
(1-833-663-5465)
To deactivate battery, score label on dotted line and move switch all Installed On
www.onelink. rstalert.com
the way to the right. Once deactivated, the alarm cannot be
www.brkelectronics.com
reactivated and must be replaced.
Replace By
ALARM GUIDE:
SMOKE ALARM: Three beeps.
CO ALARM: Four beeps.
REPLACE BATTERY: One "chirp" per minute.
MALFUNCTION: Three "chirps" per minute. Replace alarm.
END OF LIFE: Five "chirps" per minute. Replace alarm.
3055574
DEACTIVATE CONFORMS TO
UL STD 217
& UL STD 2034
1
Ionization & Photoelectric Technology
This alarm uses Photoelectric technology.
All First Alert Onelink
®
to detect particles of combustion. Smoke particles of varying number and size are produced in all fires.
Ionization Technology
Ionization technology is generally more sensitive than Photoelectric technology at detecting small particles,
which tend to be produced in greater amounts by flaming fires, which consume combustible materials rapidly and
spread quickly. Sources of these fires may include paper burning in a wastebasket or a grease fire in the kitchen.
14
SINGLE AND/OR MULTIPLE STATION SMOKE & CO ALARM
MODEL NO. 1042136
PHOTOELECTRIC
SMOKE SENSITIVITY: 0.96 – 2.45 %/ft OBSC.
W WARNING!
Carbon monoxide cannot be seen or smelled but can kill you.
If alarm signal sounds: 1. Operate Test/Silence button.
XXX-XX-XXX
2. Call your emergency services. (Fire Dept. or 911)
3. Immediately move to fresh air - outdoors or by an open door/window.
Alarm will not operate if batteries are dead, disconnected or
improperly installed. Refer to user's manual for complete battery IMPORTANT!
W
replacement list, installation, operating and safety information /
instructions. Use only batteries speci ed. Use of other batteries may
CARBON MONOXIDE SENSITIVITY: If CO levels reach
have a detrimental effect on product operations.
70ppm, it must activate within 60-240 minutes. At
MAINTENANCE AND TESTING: 150ppm within 10-50 minutes. At 400ppm within 4-15
Constant use at high or low temperatures or high humidity may reduce minutes. Refer to user's manual for more information.
battery life. Test after installation, weekly, and after cleaning. Gently Contains Transmitter Modules FCC ID:
Follow and Retain User's
vacuum monthly. Never use water, cleaners or solvents.
Manual: BRK Brands, Inc. M7U-BT1IOT and FCC ID: TLZ-CU300
HOW TO ACTIVATE ALARM: 1301 Joe Battle, Contains Transmitter Modules IC:
El Paso, TX 79936. 10190A-BT1IOT and IC: 6100A-CU300
Align alarm with mounting bracket and turn clockwise. Chasing Blue
LED's and Welcome Message indicate alarm is activated. Consumer Affairs:
Replace Alarm 10 Yrs. After Installation
1-833-ONELINK
HOW TO DEACTIVATE ALARM:
(1-833-663-5465)
To deactivate battery, score label on dotted line and move switch all Installed On
www.onelink. rstalert.com
the way to the right. Once deactivated, the alarm cannot be
www.brkelectronics.com
reactivated and must be replaced.
Replace By
ALARM GUIDE:
SMOKE ALARM: Three beeps.
CO ALARM: Four beeps.
REPLACE BATTERY: One "chirp" per minute.
MALFUNCTION: Three "chirps" per minute. Replace alarm.
END OF LIFE: Five "chirps" per minute. Replace alarm.
3055574
DEACTIVATE CONFORMS TO
UL STD 217
& UL STD 2034
2
Smoke Alarms conform to regulatory requirements, including UL217 and are designed
®
3
1.
Score label on dotted line
2. Slide switch to the right
4