Before Starting The Equipment - Gardol GAA-E 20 Li OA Instructions D'origine

Power-X-Change
20 V, 1.5 Ah .............................. 5 lithium-ion cells
20 V, 3.0 Ah ............................ 10 lithium-ion cells
20 V, 4.0 Ah ............................ 10 lithium-ion cells
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with the
Power-X charger.
Charging unit
Mains voltage ................... 200-250 V ~ 50-60 Hz
Output
Rated voltage ........................................ 21 V d. c.
Rated current ....................................... 3000 mA
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 60745.
L sound pressure level ..................... 73,9 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 84,9 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 60745.
Vibration emission value a
K uncertainty = 1.5 m/s
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Anl_GAA_E_20_Li_OA_SPK7.indb 15 Anl_GAA_E_20_Li_OA_SPK7.indb 15
= 21,251 m/s
2
h
2
- 15 -
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 3a)
Warning!
Switch off the universal saw and pull out the bat-
tery pack each time before doing any work on the
machine and changing the blade.
Open the cover (Fig. 3a/Item A) by pressing it to-
gether slightly at the front and then swinging it up.
Turn the ring (B) on the blade holder (4) as
shown in Fig. 3a until the blade (6) lets itself be
slipped into the slot of the blade holder (4). When
you now let go of the ring (B) again, the ring (B)
should return to its starting position. If this fails to
happen, try turning the ring (B) by hand into its
starting position.
Now pull on the blade to check whether it is tightly
seated in the holder.
20.10.2016 13:15:41 20.10.2016 13:15:41