Dry Vacuuming - Operation; Wet Vacuuming - Operation - Vortice Professional WD 27 Notice D'emploi Et D'entretien

unattended or within the reach of children or infirm
persons.
• If using an extension cable, make sure it rests on dry
surfaces protected against any splashes of water.
• Do not place tools or other materials on the power
cable. Do not pull or raise the appliance with the
power cable, nor move it near to sources of heat
and always unwind it completely in order to prevent
dangerous overheating.

DRY VACUUMING - OPERATION

(See figures on page 16)
(See figures on page 24)
• For WD 27/35/35 ASP models, fit the polyester
filter on the motor assembly by screwing the
filter fastening cover on anticlockwise (Fig. 2). For
the WD 35 ASP model you need to fit the polyester
fine-dust filter in the drum (Fig. 3).
all models you
• Fit the motor assembly in the drum, locking it with
the fasteners (Fig. 4).
• Insert the hose into the suction socket (Fig. 5A); to
extract it you need to move the pushbutton to the
left (Fig. 5B).
• Fit the handle onto the end of the hose, for WD
27/35 models by screwing the ring nut on
anticlockwise (Fig. 6A), for the WD 35 ASP model
by pressing (Fig. 6B). The handle has a choke
valve that shuts off or adjusts the flow of air
(Fig. 7). Press one or two pipes onto the end of the
handle as required (Fig. 8).
• Select and connect the most suitable attachment
(Fig. 9).
• To switch on the appliance, press the switch

WET VACUUMING - OPERATION

(See figures on page 18)
(See figures on page 26)
• For WD 27/35/35 ASP models, remove the
polyester filter by unscrewing the filter fastening
cover clockwise. For the WD 35 ASP model, also
remove the polyester fine-dust filter
For all
drum (Fig. 12).
• Fit the motor assembly in the drum, locking it with
the fasteners (Fig. 13).
• Insert the hose into the suction union (Fig. 14A); to
extract it you need to move the pushbutton to the
left (Fig. 14B).
• Fit the handle onto the end of the hose, for WD
27/35 models by screwing the ring nut on
12
need to fit
from the
models,
N.B.:
In order to keep the appliance in full working order
when dry vacuuming, after use it is necessary to
clean the polyester filter
polyester filter
model) by shaking them or using a brush (Fig. 22-23).
Occasionally these filters can be washed with water
using a brush (fig.22-23).
and put back in when thoroughly dry.
the motor assembly after plugging in to a power
socket (Fig. 10).
• It is possible to use an electric tool together with
the Professional WD 35 ASP appliance (Fig. 11):
- insert the adapter
fitting it on the outlet connector of the electric
tool.
- insert the Shuko plug of the electric tool into the
socket of the WD 35 ASP appliance.
Schuko
For automatic operation of the WD 35 ASP
vacuum cleaner, using the electric tool, press the
switch onto position (=). The appliance will start
up simultaneously with the electric tool since it has
an electronic card.
The WD 35 ASP appliance is equipped with a
device that permits delayed switch-off.
• CAUTION: The max power of the supplementary
attachment socket is 2000W.
Do not connect attachments with a higher power.
on
anticlockwise (Fig. 15A), for the WD 35 ASP model
by pressing (Fig. 15B).
The handle has a choke valve
completely.
• Press one or two pipes onto the end of the handle
as required (Fig. 16).
• Fit the specific adapter for liquids onto the nozzle
(Fig. 16).
• To switch on the appliance, press the switch
the motor assembly after plugging in to a power
socket (Fig. 17).
(motor assembly) and the
(drum - Professional WD 35 ASP
(all models) by shaking them or
onto the end of the hose,
that must be shut
EN
on