Lcd Display; Mode Selection - RIDGID R84086 Manuel D'utilisation

OPERATION
FOLD-DOWN ROTATABLE FLEXIBLE ANTENNA
See Figure 3, page 11.
To improve radio reception, rotate the antenna or move the
radio to a higher elevation. The antenna folds down and out
of the way when not in use.

LCD DISPLAY

See Figure 4, page 11.
NOTE: The illustrations of the LCD display shown in this
manual are only examples of the frequencies you may see
on your radio and are not the exact frequencies that you
may choose to listen to.
When the radio is not connected to a power supply, the LCD
display will remain off. If the radio is connected to a power
supply and in the ON position, LEDs will light the display.
You can view the time, frequency, and settings in use on
the LCD display.
NOTE: Always disconnect battery packs after use to prevent
draining the battery pack.
ON/OFF/VOLUME
See Figure 4, page 11.
Push the ON/OFF/VOLUME knob to turn the radio ON or
OFF.
NOTE: You may need to keep the button pressed for up to
3 seconds before the radio will start. If this happens, replace
the radio's AAA batteries.
To increase the volume: turn the ON/OFF/VOLUME knob
clockwise.
To decrease the volume: turn the ON/OFF/VOLUME knob
counterclockwise.
To help preserve battery power, the radio will automatically
enter sleep mode approximately 1 hour after it is turned off.
To exit sleep mode and restart the radio, you must use the
ON/OFF/VOLUME knob on the radio.
SETTING THE CLOCK
See Figure 4, page 11.
When the time is set, it will appear on the LCD display by
default whenever the radio is on. To set the clock:
NOTE: Install the battery pack before setting the clock.
 Press the CLOCK button and hold for 3 seconds until
clock begins to blink.
 Press and release the CLOCK button to scroll through
the hour, minute, and 12-hour/24-hour settings.
 While each setting is highlighted, use the volume knob
or arrow buttons to adjust as desired.
 Once the desired time and 12-hour/24-hour setting has
been entered, press the CLOCK button again to set.

MODE SELECTION

See Figure 4, page 11.
Press the MODE button to cycle through available modes.
There are four modes to choose from:
 FM mode
 AM mode
 AUX: For the 3.5 mm input jack
 BLUETOOTH ®
capable devices
NOTE: This mode can also be accessed directly by using
the button.
When turned on, the radio will return to the last mode that
was used if the battery pack was not disconnected. In the
event all power is lost to the radio, the display will default
to FM mode.
AM/FM TUNING
See Figure 4, page 11.
The left and right arrow buttons and the MODE button are
used to tune to the desired radio frequency. The selected
frequency is displayed on the LCD.
 Press the MODE button until AM or FM appears.
 Press and release the left arrow button to tune to a lower
frequency. Press and release the right arrow button to
tune to a higher frequency.
Briefly push either button (not press and hold) to tune one
frequency step at a time.
 To SEEK, press and hold desired arrow button for 3 sec-
onds to tune to the next frequency with clear reception.
 To SCAN, press and hold both arrow buttons for 3 sec-
onds to scan through all the frequencies with clear
reception.
NOTE: When scanning, the radio will stop on frequencies
with clear reception for three seconds before continuing
to the next higher frequency.
Press PRESETS to stop scanning and select a frequency.
If no frequency is selected, the radio will return to the
frequency that was displayed when the scan was started.
STORING A PRESET IN MEMORY
See Figure 4, page 11.
The memory feature saves up to 20 frequencies as presets
in the radio's memory. You can save 10 frequencies in FM
mode and 10 in AM mode.
To store a frequency in memory:
 Tune to the frequency you want to save.
 Press and hold the PRESETS button for 3 seconds. A
memory location number will blink on and off.
6 - English
: Listening to audio from BLUETOOTH ®