Start Operating Set-Up - Whirlpool W10726004B Instructions D'installation

Start Operating Set-up

Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a new
commercial washer, hook it up, plug it in, and have a washer
that operates.
Washers are preset at the factory for an 11-minute wash period
and 3 rinses (no extra rinse).
SET-UP CODES
The WARM button will advance you from code to code.
■
The HOT button will change the code value.
■
The COLD button will select or deselect options.
■
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE: The first line of each code indicates the factory default
for 9050 models.
CODE
REGULAR CYCLE PRICE (Factory Default)
6 01
6 01 When the d.xx is set to d.CS, this 6 xx value
represents the number of push-in actuations of the
coin slide to start the washer. 6 01 would equal one
coin slide activation.
6 00 When the d.xx is set to d.00, this 6 xx value
represents the number of coins needed to start the
washer; may adjust from 0–39. Change this value
by pressing the HOT button. 6 07 = 7 coins. 9060
models default to 6 00.
g
Press the WARM button once to advance
to next code.
ADDITIONAL RINSE OPTION
8 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
8 00 Not Selected 'OFF'.
8 Ar Selected 'ON'.
Press the COLD button once for this selection.
Press the WARM button once to advance
g
to next code.
CYCLE COUNTER OPTION
9 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
9 00 Not Selected 'OFF'.
9 0C Selected 'ON' and not able to be deselected.
Press the COLD button 3 consecutive times to select
'ON'. Once selected 'ON' it cannot be deselected.
Press the WARM button once to advance
g
to next code.
EXPLANATION
CODE
MONEY COUNTER OPTION
1. 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
1. 00 Not Selected 'OFF'.
1. 0C Selected 'ON'.
Press the COLD button 3 consecutive times to
select 'ON' and 3 consecutive times to remove
(Not Selected 'OFF'.) Counter resets by going
from 'OFF' to 'ON'.
1 C0 Selected 'ON' and not able to be deselected.
To select 'ON' and not able to be deselected,
first select 'ON', then within 2 seconds, press
the COLD twice, HOT once, and exit the set-up
mode.
g
Press the WARM button once to advance
to next code.
2. 00 This option is not available.
VALUE OF COIN 1
b. 40
b. 05 This represents the value of coin 1 in number
of nickels: 05 = $0.25.
By pressing the HOT button, there is an option
of 1–199 nickels.
With coin slide activation, this represents the total
vend price in nickels. Example: b.40 is equal to
$2.00.
g
Press the WARM button once to advance
to next code.
C. 20 VALUE OF COIN 2
C. 20 This represents the value of coin 2 in number
of nickels: 20 = $1.00.
C. 05 By pressing the HOT button, there is the option
of 1–199 nickels.
Press the WARM button once to advance
g
to next code.
d. CS COIN SLIDE OPTION
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'. Press the COLD button 3
consecutive times to select/deselect this option.
d. CS Selected 'ON'. (Default for 9050 models)
When coin slide mode is selected, set 'b'. equal to
value of vend price in nickels. Set set-up code 6 xx
(regular cycle price) to number of slide operations. If
the installer sets-up 'CS' and a coin drop mechanism
is installed, the washer will not
register coins that are inserted.
d. 00 Not Selected 'OFF'. (Default for 9060 models)
Press the WARM button once to advance
g
to next code.
EXPLANATION
11