Narex EV 13 G-2 Manuel D'utilisation page 14

English
Table of contents
Description of the device ..................................................................14
Technical Specification .....................................................................14
General Power Tool Safety Warnings .............................................14
Special Safety Instructions ...............................................................15
Information about noise level and vibrations ..............................15
Double insulation ..............................................................................15
Use .......................................................................................................15
Commissioning and use ...................................................................15
Work instructions ..............................................................................16
Maintenance and service .................................................................16
Accessories..........................................................................................16
Storage ................................................................................................16
Environmental protection ................................................................16
Warranty .............................................................................................17
Certificate of Conformity ..................................................................17
Technical Specification
Model
Supply voltage (V)
Power frequency (Hz)
Power input (W)
Speed under load (rpm)
1st speed gear
2nd speed gear
Idle speed (rpm)
1st speed gear
2nd speed gear
Speed pre-selection
Right-left turning
Extent of chuck dia. (mm)
Thread on spindle
Quick-tightening chuck Auto-Lock
Drilling dia. max (mm)
into steel
into aluminium
into wood
Clamping neck dia. (mm)
Weight (kg)
Protection class
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference!
The term "power tool" in the warnings refers to your mains-operat-
ed (corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b) Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust. Pow-
er tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a pow-
er tool. Distractions can cause you to lose control.
14
Drill EV 13 G-2, EV 13 G-2A
Original operating manual (EN)
Description of the device
1 .......Chuck with ring gear
2 .......Spots on spindle
3 .......Clamping neck
5 .......Air vents
6 .......Latching pin
7 .......Switch / controller
8 .......Speed pre-selection wheel
9 .......Alteration switch lever
10 .....Gear-shifting lever
11 .....Additional handle
12 .....Stop bar
13 .....Chuck hook
14 .....Spanner
15 .....Socket screw wrench
16 .....Quick-tightening chuck
Depicted or displayed accessories need not necessarily be-
come the integral part of delivery.
EV 13 G-2
230-240
50-60
760
0-600
0-1 750
0-1 100
0-3 050
ü
ü
1.5-13
1/2"-20 UNF
û
13
25
45
43
2.0
II /
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for out-
door use reduces the risk of electric shock.
EV 13 G-2A
230-240
50-60
760
0-600
0-1 750
0-1 100
0-3 050
ü
ü
1.5-13
1/2"-20 UNF
ü
13
25
45
43
2.1
II /