Télécharger Imprimer la page

Imiola HAK-POL P/032 Mode D'emploi page 5

Publicité

• Odkręcić tylne lampy, zdemontować zderzak i belkę zderzeniową
( nie będzie potrzebna).
• Element E i F przykręcić lekko śrubami M8x50 8.8 (pkt 6) i element G i H
śrubami M12x40 8.8 (pkt 4).
• W podłużnicach (na zewnętrznych stronach) odszukać po jednym zaślepionym
otworze M10. Udrożnić je.
• Elementy C i D przykręcić lekko śrubami M10x40 8.8 (pkt 1).
• Belkę haka A wsunąć między elementy i przykręcić śrubami M12x40 8.8 (pkt 2,5)
• Dokręcić wszystkie śruby z momentem wg tabeli.
• Zamontować zderzak.
• Przykręcić kulę i blachę gniazda elektrycznego śrubami M12x70 8.8.
• Podłączyć instalację elektryczną (zastosuj wiązkę z modułem).
• Unscrew the rear lights.
• Disassemble the bumper.
• Unscrew the bolts M8x50 8.8 from the rear belt on the left of the reinforcement the bumper (the part
of the reinforcement will not be used any more).
• Screw slightly the element D with bolts M8x50 8.8.
• Unscrew the bolts M8x50 8.8 on the right of the reinforcement (point 1), (the part
of the reinforcement will not be used any more).
• Screw slightly the element E with bolts M8x50 8.8 (point 2).
• Find one blind hole M10 in every metal clamps (on the outsides). Make them permeable.
• Screw the elements B and C to the metal clamps with bolts M10x40 8.8 (point 3 and 4).
• Screw the main bar to the elements B and C with bolts M12x40 8.8 (point 5 and 6).
• Screw the elements F and G to the main bar A
and to the elements D and E with bolts M12x40 8.8 (point 7, 8, 9, 10), look at the drawing.
• Tighten all the bolts according to the torque setting- see the table.
• Assemble the bumper.
• Fix the ball and electric plate with bolts M12x70 8.8.
• Connect the electric wires (use the electronic module).
• Dévisser les phares arrière.
• Déposer le pare-chocs,
• Dévisser les boulons M8x50 8.8 de la partie arrière, coté gauche de renfort de pare- chocs
(partie de renfort de sera plus remontée).
• Visser legèrement l'élément D avec les boulons M8x50 8.8.
• Dévisser les boulons M8x50 8.8 (point 1), coté gauche de renfort (partie de renfort ne sera plus utilisée).
• Visser legèrement l'élément E avec les boulons M8x50 8.8 (point 2).
• Rechercher une ouverture bouchée M10 par chaque longeron (coté extèrieur). Débouchet les.
• Visser les éléments B et C aux longerons avec les boulons M10x40 8.8 (point 3 et 4).
• Visser la traverse aux éléments B et C par les boulons M12x40 8.8 (point 5 et 6).
• Visser l'élément du crochet F et G à la traverse du crochet A et aux éléments D et E par les
boulons M12x40 8.8 (point 7, 8, 9, 10), voir le croquis.
• Serrer tous les boulons avec un couple de serrage selon tableau.
• Poser le pare-chocs.
• Visser la boule et tôle de la prise électrique par les boulons M12x70 8.8.
• Raccorder le circuit électrique (utiliser le faisceau avec module).

Publicité

loading