essentiel b MOUV TV 32-75 Notice D'utilisation page 9

Operating instructions
BEFORE INSTALLING THIS PRODUCT, IT IS IMPORTANT TO READ AND UNDERSTAND THE
INSTALLATION INSTRUCTIONS COMPLETELY IN ORDER TO AVOID PHYSICAL INJURIES AND
MATERIAL DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN A PLACE WHICH IS EASILY
ACCESSIBLE SO YOU CAN CONSULT THEM AT A LATER DATE.
The safety instructions must be followed throughout the installation of this product. User safety
equipment and suitable tools for installation in order to avoid physical injury.
If the product were to be sold or given to
•
another person, make sure that the operating
instructions are passed on with it and that no
parts are defective.
This wall mount bracket is able to support
•
a maximum load of 60 kg for screens with a
diagonal measurement of 32" to 75" maximum.
Ensure that the wall structure can support such
a load.
The weight of the screen must not exceed the
•
maximum load capacity of the bracket.
It is essential that you follow a correct installation
•
procedure. This must be carried out by a qualifi ed
person. Non-compliance with the installation
instructions may lead to severe physical injury,
linked to falling or incorrect handling of the screen.
Do not install the bracket on a structure which is
•
subject to vibrations, movement or which may
be subject to impacts. Non-compliance may
lead to the screen being damaged or the surface
of the bracket being damaged.
Do not install the bracket in a place of passage in
•
order to avoid knocks and injuries (above a bed,
a chair, a door or in a corridor...).
Do not install the bracket near heating, a
•
fi replace, direct sunlight, air-conditioning or
other sources of direct heat.
Non-compliance may lead to the screen being
•
damaged and may increase the risk of fi re.
16
V.2.0
Operating instructions
Do not install the bracket in a very damp environment.
•
One month after installation, check that all the
•
screws are tight and that the wall plate has been
correctly attached to the wall.
Please note: please check that there are no
•
cables or pipes behind the wall to which you
wish to attach your bracket!
Check the position of the electric cables when
•
you install or handle the wall bracket, in order to
avoid any pinching or deterioration of the cables.
The screw fi xings supplied with this wall bracket
•
are intended exclusively for fi xing to a wall made
up of solid bricks or concrete.
For installation on any other medium (wood,
•
hollow bricks, plasterboard surfaces, steel...)
please contact an approved professional
installer, and use the appropriate equipment.
Before beginning installation, please check
•
the composition of your wall. Do not install the
bracket on old or badly sealed brickwork, on a
plasterboard surface or wood panelling.
Keep children away from the installation and
•
ensure that they cannot play with the appliance
subsequently.
The packaging material (packaging paper,
•
polystyrene) can be dangerous for children: there
is a risk of suffocation. Do not leave packaging
material within reach of children!
V.2.0
Operating instructions
installation of wall plate
The screw fi xings supplied with this wall bracket are intended exclusively for fi xing to a wall
made up of solid bricks or concrete. For installation on any other medium, please contact
an approved professional installer, and use the appropriate equipment
60mm
Insert a concrete rawl plug in each hole. If necessary, you can use a hammer to lightly tap each rawl
plug, so they are at the same level as the wall. Once the rawl plugs are in place, position the wall plate.
Attach the washers and then the lag screws into the rawl plugs which project slightly from the wall, as
indicated in the diagram below.
6
5
V.2.0
installation of wall plate
Begin by positioning the drilling template against the wall
using the spirit level to keep it straight.
Use adhesive or drawing pins to hold the template against
the wall while you drill six holes which will be used to attach
the bracket.
Drill the holes with an electric drill and a 10-mm concrete bit.
Remove the template and place to one side.
10mm
!
Do not tighten completely until all
•
the screws are in place.
Do not overtighten the screws.
•
This can
needlessly.
Do not release the wall bracket
•
before it is firmly attached to
the wall.
damage the wall
17
V.2.0
istallation of wall