Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
PRODUCT DESCRIPTION AND RECOMMENDATION
This arm blood pressure monitor is an electronic device intended to make
human blood pressure and pulse rate at arm of adult population.
In order to get reliable measurements, keep taking and recording blood
pressure measurement at the same time every day and avoid eating,
bathing, smoking, exercising, ingest caffeine or alcohol at least 30 minutes
prior to take measurement.
Be seated and relax for at least 5 minutes before measuring
Make sure the cuff is at heart level for taking measurement
To make repeated measurements, the rest interval between measurements
shall not be less than 3 minutes.
Consult your physicians for interpretation of blood pressure measurement
and follow their direction.
This blood pressure monitor could be used with Thomson healthcare app
downloadable on Apple Store and Play Store. The app is also suitable with
Apple Health Kit.
TIPS FOR MEASUREMENT
It can cause inaccuracy if the measurement is taken in the following
circumstances:
Within 1 hour after dinner or drinking
Immediate measurement after tea, coffee, smoking
Within 20 minutes after taking a bath
When talking or moving your fingers
In a very cold environment
When you want to discharge urine
SECURITY
This arm blood pressure monitor can be only used for which it has been
designed as explained in the instruction booklet
Consult your physician for health status and blood pressure range before
taking measurement at home with this device
Do not press the power button if the cuff has not been properly wrapped
If the cuff causes you any discomfort during measurement, press the power
button to turn off the device immediately
Pull off the Velcro strap to detach the cuff if the cuff pressure exceeds
300mmHg without an automatic exhaust
Do not modify or try to repair yourself this device
MAINTENANCE
Clean your device with a soft dry cloth, lens with a cotton swab
moistened with water then wipe it dry
Do not store the device with direct sunlight and keep it away water
Remove batteries from your device if you don't use for a long time
OVERVIEW
ON/OFF BUTTON
DATA
IPD (irregular
TRANSMISSION
pulse detection)
SYMBOL
SYSTOLIC
DIASTOLIC
PULSE RATE
USER 2
BUTTON
QUERY
USER 1
BUTTON
BUTTON
INITIAL START-UP
Use the AC power adaptator by connecting to the blood pressure monitor
to reload the Li-polymer battery.
Before using the device, please make sure that the ON/OFF BUTTON is
ON.
Setting Date, Time and Measurement Unit
Press the USER 1 BUTTON during 3 seconds until the hour on the left of
the screen display starts to flash.
Press the left button "mode" to set the hour. Each press is increasing the
number of hour.
To confirm the hour, press the USER 1 BUTTON then the numeral
representing minute starts to blink.
Repeat the previous steps to set the time.
Repeat the previous steps to set the month, day, year.
After confirming [YEAR], the LCD will display „dONE" and the monitor will
shut off automatically
It's ready to take measurements.
PAIR-UP THE BPM WITH YOUR DEVICE
Turn on Bluetooth and the Thomson Healthcare app. Please make sure that
both are working.
Launch the app to start the pair-up. For more informations about using the
Thomson Healthcare app, please visit our website:
When the monitor is OFF, press and hold the START button for 2 sec to start
the pair-up. The following symbols appear on the display which means the
pair-up is in progress.
Then, one of the two following symbols will appear :
If succeed
If fail
TO TAKE A MEASUREMENT
1- Remove all accessories (watch, bracelet, etc) from your left wrist. If your
physician has diagnosed you with poor circulation in your left arm, use your
right arm
2- Roll or push up your sleevse to expose the skin
3- Apply the cuff to your left wrist with your palm facing up
4- Position the edge of the cuff about 2-3 cm of the elbow with your palm up.
5- Fasten the arm cuff around your arm, leaving no extra room between the
cuff and your skin. If the cuff is too loose, the measurement will not be
accurate
6- Resting for 5 minutes before measuring
7- Wait at least 3 minutes between measurements
8- For a meaningful comparison, try to measure under similar conditions. For
example, take daily measurement at approximately the same time, on the
same arm, or as directed by a physician
START THE MEASUREMENT
Press START to turn ON the monitor then press your user button, it will
complete the measurement process automatically.
This device will proceed to data transmission automatically after
measurement. The Bluetooth symbol blinks.
RECALLING THE RECORDS
Press „QUERY" button to access to memory the select the user
Press "QUERY" again to visualize one by one all the measurements. The
blood pressure monitor can store 60 measurements by user.
DELETING THE RECORDS
To delete a record, press the QUERY BUTTON during 3 seconds. When the
message "dEL ALL" display on the screen, press QUERY BUTTON again.
TROUBLE SHOOTING
The display is dim or is not lighting up
Check out if the batteries are exhausted or inserted correctly. If they are
exhausted, replace the 2 batteries at the same time with new one.
Data communication has failed
Make sure that phone's Bluetooth is on or within the distance range
E1 : Inflation is slow or the cuff is not secure
Refasten the cuff and then measure again
E2 : The cuff is very tight
Refasten the cuff ans then measure again
E3 : The pressure of the cuff is excess
www.thomson-hc.eu
Refasten the cuff and then measure again
E5 /E6 : System error occurred
Retake the measurement. If the problem persist, contact the retailer or our
customer service department for assistance
E10 / E11 : The monitor detected motion while measuring
Movement can affect the measurement. Relax for a moment and then
measure again
E20 : The measurement process does not detect the pulse signal
Loosen the clothing on the arm and then measure again
E21 : Measure incorrectly
Publicité
