Installation Instructions - Garmin GHS 11 Instructions D'utilisation

GHS™ 11

Installation Instructions

Important Safety Information
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
When drilling or cutting, always check what is on the opposite
side of the surface.
Tools Needed
• Pencil
• Drill
7
• 22 mm ( / in.) drill bit or hole saw
8
1
• 3 mm ( / in.) drill bit
8
3
• 4.76 mm ( / in.) wrench
16
• Phillips screwdriver
• Marine sealant (optional)
Mounting Considerations
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
When selecting a mounting location, observe these
considerations.
• To avoid interference with a magnetic compass, do not install
the device closer to a compass than the compass-safe
distance value listed in the product specifications.
• A 10 m (32 ft) extension cable is included to connect the
handset to the VHF radio. You must select a mounting
location for the handset that allows this extension cable to
connect to the back of the VHF radio.
• You can use the included screws to mount the extension
cable and the handset cradle mount on your boat. If the
included screws are not appropriate for the mounting surface,
you must purchase suitable hardware.
Installing the Extension Cable in the Mounting
Surface
Before drilling a hole to mount the extension cable, you must
make sure that the extension cable is long enough connect to
the back of the VHF radio from the selected mounting location.
1
Using the mounting plate
hole in the center of the mounting plate and mark the screw
locations.
2
WARNING
CAUTION
NOTICE
NOTICE
as a template, trace the cable
2
Set the mounting plate aside.
Do not drill through the mounting plate.
3 7
Using a 22 mm ( / in.) drill bit or hole saw, drill the center
8
cable hole in the mounting surface.
4 1
Using a 3 mm ( / in.) drill bit, drill the pilot holes.
8
5
Apply marine sealant between the mounting plate and the
mounting surface to help seal the holes (optional).
6
Using the included screws, attach the mounting plate to the
mounting surface.
7
Connect one end of the extension cable to the microphone
relocation port on the back of the VHF radio, and route the
other end of the extension cable to the mounting location.
8
Feed the extension cable connector
the mounting surface.
9
Apply marine sealant around the extension cable connector
in the mounting plate to help seal the hole (optional).
10
Secure the extension cable connector to the mounting plate
using the weather cap
11
Connect the handset to the extension cable.
Installing the Cradle Mount
1
Select a mounting location near the extension cable.
TIP: You can place the handset in the cradle mount, connect
the handset to the extension cable, and hold it against the
mounting surface to help determine the best location.
2
Using the cradle mount as a template, mark the screw
locations.
3
Set the cradle mount aside.
Do not drill through the cradle mount.
1
4
Using a 3 mm ( / in.) drill bit, drill the pilot holes.
8
5
Using the included screws, secure the cradle mount to the
mounting surface.
Specifications
Specification Measurement
Dimensions (H×W×D) 154 × 69 × 40 mm (6.1 × 2.7 × 1.6 in.)
Weight 318 g (11.22 oz.)
Temperature range Operating: From -15° to 70°C (from 5° to
158°F)
Storage: From -20° to 70°C (from -4° to
158°F)
Compass-safe distance 60 cm (23.6 in.)
Water rating IEC 60529 IPX7*
*The device withstands incidental exposure to water of up to 1 m
for up to 30 min. For more information, go to
/waterrating.
through the back of
and the nut .
www.garmin.com
Installation Instructions