Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

Instructions Manual-Gebruiksaanwijzing-Manuel d'instruction
EN - Important instructions
Safety precaution
1. Read all instructions carefully before you use the appliance.
2. Remove the packages and ensure that the appliance is undamaged. In case
of doubt do not use the fan and contact with your supplier.
3. Do not let children play with parts of the packages (such as plastic bags).
4. Before plugging to the socket, check that if the voltage of your main supply
matches the voltage marked on the rating label of the appliance.
5. Before assembling or dismantling the fan, must sure that the fan is unplugged.
6. Before unplugging the power cord, be sure to turn off the power.
7. Do not insert any object into the guard while the fan is operating, IT WILL
CAUSE INJURY TO THE PERSON.
8. The fan shall be used for temperate climates, Do not use the fan at the high
humidity area or dusty area. Do not use the fan where acid or alkali is stored.
9. Do not hang any clothes or garment on the fan guards.
10. Do not use the fan outdoors.
11. Do not continuously to blow the baby or the patient directly for a long time.
12. The appliance is not intended for use by young children or infirm persons
without supervision.
13. Young children should be supervised to ensure that they do not play with the
appliance.
14. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Parts of description
Art nr. 66.000.000.15
Control panel
Speed control button
Rear enclosure
Power cord
Plug
Rear base
Clip
Screw
Sensor zone
Front enclosure
Turn desk
Screw
Front base
1

Publicité

Table des Matières
loading

Sommaire des Matières pour Airmate 66.000.000.15

  • Page 1 Parts of description Control panel Speed control button Sensor zone Rear enclosure Front enclosure Power cord Plug Turn desk Screw Rear base Clip Front base Screw Art nr. 66.000.000.15...
  • Page 2 2. Insert the rotor desk of main into the base, then fasten the screw, make sure the main and base connect firmly. 3. Remove the screw and the clip from the base, put the power cord into the clip slot, close the clip and tighten the screw. Art nr. 66.000.000.15...
  • Page 3 2 HR 4 HR 8 HR  OFF Press the button, the fan stop running. Note: When mode of Rhythm wind or Sleep wind is selected, the fan will continually cycle through Low, Medium, and High setting. Art nr. 66.000.000.15...
  • Page 4 3. Follow assembly instructions in reverse order, get the fan back to the carton and store the fan at dry place. Specifications Power supply voltage: 220-240V, 50Hz. Power consumption: 30W. Protection class: II. Produced in P.R. China. Art nr. 66.000.000.15...
  • Page 5 Control panel Onderdeelbeschrijving Speed control button Sensor zone Rear enclosure Front enclosure Power cord Plug Turn desk Screw Rear base Clip Front base Art nr. 66.000.000.15 Screw...
  • Page 6 2. Steek de rotorstandaard in de basis, draai de schroef vast en controleer of de standaard en de basis goed zijn verbonden. 3. Verwijder de schroef en de klem uit de basis, plaats de stroomkabel in de klemsleuf, sluit de klem en draai de schroef vast. Art nr. 66.000.000.15...
  • Page 7: Bedieningsinstructies

    4 HR 8 HR  OFF Druk op de knop om de ventilator te stoppen. Let op: bij selecteren van de modus Rhythm (pulserend) of Sleep (slaapwind) zal de ventilator continue de instellingen laag, gemiddeld en hoog doorlopen. Art nr. 66.000.000.15...
  • Page 8: Gebruik Van De Afstandsbediening

    2. Verwijder de olie of vlekken van de behuizing om schade aan de ventilator te voorkomen. 3. Volg de bovenstaande stappen in omgekeerde volgorde, plaats de ventilator in de doos en bewaar deze op een droge locatie. Specificaties Voltage stroomvoorziening: 220-240V, 50Hz Stroomverbruik: 30W Beschermingsklasse: II. Geproduceerd in P.R. China. Art nr. 66.000.000.15...
  • Page 9: Mesure De Sécurité

    à l'appareil par une personne responsable de leur sécurité. Control panel Description des pièces Speed control button Sensor zone Rear enclosure Front enclosure Power cord Plug Turn desk Screw Rear base Art nr. 66.000.000.15 Clip Front base Screw...
  • Page 10: Assemblage De La Base

    2. Insérer le plateau du rotor dans la base puis serrer la vis, s'assurer que le bloc principal et la base sont bien connectés. 3. Retirer la vis et le clip de la base, insérer le cordon d'alimentation dans la fente du clip, fermer le clip et serrer la vis. Art nr. 66.000.000.15...
  • Page 11: Instruction De Service

     OFF Le ventilateur cesse de fonctionner lorsque ce bouton est actionné. Note: lorsque le mode de flux rythmé ou de sommeil est sélectionné, le ventilateur basculera continuellement entre le réglage de vitesse faible, moyenne et haute. Art nr. 66.000.000.15...
  • Page 12: Entretien

    Elka Pieterman B.V.B.A. Prinsenhil 1 Vosveld 14 4825 AX Breda 2110 Wijnegem The Netherlands Belgium Tel. +31 (0)76-593 93 93 Tel. +32 (0)3 326 32 40 Fax +31 (0)76-593 93 50 Fax +32 (0)3 326 22 85 info@elka.nl info@elkapieterman.be Art nr. 66.000.000.15...

Table des Matières