IMG STAGELINE WSA-50WIFI Mode D'emploi page 7

3 Setting the Adapter into Operation
1) Find a suitable position for the WSA-
50WIFI, then set the WSA-50WIFI up and
put the antenna (1) in a vertical position.
2) Connect the XLR jacks or jacks OUTPUT (8)
to the input (e. g. LINE, CD, AUX) of the
subsequent unit (e. g. amplifier, mixer,
active speaker system).
3) Switch on the audio unit connected to the
jacks OUTPUT and adjust it to a normal
volume.
4) Connect the power supply unit supplied to
the jack DC IN (7) and to a mains socket
(230 V~/50 Hz). (For convenient operation,
connect the power supply unit to a power
strip with on/off switch.) The POWER indi-
cator (6) will light up.
After a while, the LED AP (2) or STA (5)
will light up to indicate the mode set. The
mode set will also be announced in Eng-
lish via the audio output (8) ["AP mode is
starting ..." or "STA mode is connected"].
Use the control LEVEL (4) to adjust the
volume.
5) For direct connection of the WSA-50WIFI
to the signal source, use the Access Point
mode (AP); for connection via a wireless
local network (WLAN), use the Station
mode (STA). To switch between the modes,
press the button MODE (3) for approx.
3 seconds until the LED for the mode de-
sired starts flashing. The change will also
be announced via the audio output.
Always switch on the AP mode when
establishing a connection for the first time!
3.1 Direct connection to the signal source
1) The LED "AP" (2) must be illuminated;
otherwise see chapter 3, step 5.
2) At the signal source (smartphone, tablet
PC, etc.), switch on the WLAN function.
3) Connect the signal source to the WSA-
50WIFI.
4) Enter the password "87654321".
5) At the signal source, start the audio out-
put and adjust the volume. If required,
switch the audio output from the speaker
system to "WSA-50WIFI".
6) If required, readjust the volume at the
audio amplifier.
3.2 Connection via WLAN
1) The LED "AP" (2) must be illuminated;
otherwise see chapter 3, step 5.
2) At the signal source, call up the following
IP address via a web browser:
http://192.168.0.1
The page "WiFi Music" for network selec-
tion will appear.
3) Select the network into which the WSA-
50WIFI is to be integrated and enter the
password for the network.
4) Then click "submit". Once the configu-
ration has been completed, the message
"Set up successfully, Restarting ..." will
appear. The WSA-50WIFI will switch to the
STA mode after approx. 1 minute.
5) Connect the signal source to the network
in which the WSA-50WIFI is located. Start
the audio player and adjust the volume.
6) If required, readjust the volume at the
audio amplifier.
4 Specifications
Audio frequency range: . . . 20 – 20 000 Hz
THD: . . . . . . . . . . . . . . . . . . < 0.1 %
Channel separation: . . . . . . > 90 dB
S/N ratio: . . . . . . . . . . . . . . > 85 dB
Output
Level: . . . . . . . . . . . . . . . 775 mV max.
Connection: . . . . . . . . . . XLR, 6.3 mm jack
Transmission frequency: . . . 2.404 GHz – 2.476 GHz
Range (w/o obstacles)
AP mode: . . . . . . . . . . . . > 20 m
STA mode: . . . . . . . . . . . > 50 m
WLAN standard: . . . . . . . . . IEEE 802.11b/g/n
Audio formats: . . . . . . . . . . MP3, FLAC, WAV, APE,
Data rate: . . . . . . . . . . . . . . up to 7 Mbit/s
Power supply: . . . . . . . . . . . 5 V⎓ via PSU supplied
Dimensions (w/o antenna): . 130 × 54 × 130 mm
Weight:. . . . . . . . . . . . . . . . 516 g
Subject to technical modification.
All rights reserved by MONACOR
GmbH & Co. KG. No part of this instruction manual
may be reproduced in any form or by any means
for any commercial use.
WMA, AAC
and connected to
230 V~/50 Hz
INTERNATIONAL
®
7