Electrical Connection - Gardol GEV 1400-33/1 Mode D'emploi D'origine

tube beforehand.
•
Now screw the tubes together using the
screws supplied (Fig. 6/Item 3), the plastic
sleeves (Fig. 6/Item 4) and the star screw
(Fig. 6/Item 5).
Fitting the upper push bar (see Fig. 7)
•
Position the upper push bar (Fig. 7) such that
its holes line up with the holes of the lower
bar.
•
Now screw the tubes together using the
screws supplied (Fig. 7/Item 1), the plastic
sleeves (Fig. 7/Item 2) and the star screw
(Fig. 7/Item 3).
•
Using the cable clips supplied (Fig. 8), attach
the power cable to the tubes of the push bars
so that it is possible to open and shut the
ejector flap (Fig. 9/Item A).
Please ensure that the ejector fl ap can be opened
and closed easily!
Adjusting the handlebar height (see Fig. 17)
Loosen the star screw (Fig. 17/Item 1) on both
sides of the scarifi er by turning several revolu-
tions. Now adjust the handlebar to the desired
height.
Notice!
The height of the handlebar may be adjusted
within the mark (Fig. 17/Item V) during operation.
Retighten the star screws.
The identical tilt angle must be set on both sides.
Assembling the grass basket (see Figs. 10
-13)
•
Push both frame parts into each other (Fig.
10).
•
Pull the grass basket over the metal frame
(Fig. 11).
•
Pull the rubber clips over the metal frame
(Fig. 12).
•
To hang the grass basket on the scarifier you
must lift the ejector flap (Fig. 13/Item 1) with
one hand and with the other hand take hold of
the grass bag by the handle and hook it onto
the scarifier from above (Fig. 13).
Danger!
Before you ever hook the grass basket to the sca-
rifi er you must ensure that the motor is switched
off and the cutting unit is not rotating.
Anl_GEV_1400_33_1_SPK7.indb 18 Anl_GEV_1400_33_1_SPK7.indb 18
GB
Adjusting the scarifi er depth (see Fig. 14)
The scarifi er depth is adjusted at both front
wheels via the adjustment mechanism. For this,
pull out the adjusting screw and turn the wheel to
the left or right into one of the available positions
(0/I/II/III).
0 = drive/transport position
I = scarifi er depth 3 mm
II = scarifi er depth 7 mm
III = scarifi er depth 9 mm

Electrical connection

The equipment can be connected to any normal
socket with 230V AC. It is only acceptable to con-
nect it to a shockproof socket with a 16A circuit
breaker. Furthermore, a residual-current-operated
protective device with max. 30 mA should be con-
nected upstream.
Power cable
Please only use power cables that are not dama-
ged. The total length of the power cable should
not exceed 50 meters; going beyond this distance
will reduce the power output of the electric motor.
The power cable must have a cross-section of 3 x
1.5 mm2. The insulating sheath of scarifi er power
cables is frequently damaged.
Some of the causes for this are:
•
Cracking from running over the cable
•
Pinching when the power cable is dragging
under doors and pulled through windows
•
Cracking due to old age of the insulation
•
Kinking by improperly fastening or guiding the
power cable
The power cables must, at the very minimum, be
of type HO5RN-F and 3-stranded. The cable type
must be printed somewhere on the power cable.
Only purchase power cables that are marked as
such! Plugs and socket couplers for the power
cables must be made from rubber and be splash-
proof. There is a limit to how long power cables
can be. Longer power cables require larger con-
ductor cross-sections. Power cables and connec-
ting lines must be regularly checked for damage.
Ensure that the lines are de-energized before
checking them. Completely unwind the power
cable. Also check power cable entry points, plugs
and socket couplers for kinks.
- 18 -
31.01.2017 09:50:59 31.01.2017 09:50:59