Lcd Screen; Operating Instructions; Charging The Internal Battery; Using The Usb Ports - Schumacher Electric SL1460 Guide D'utilisation

5.

LCD SCREEN

CHARGING
INDICATOR
BATTERY
CAPACITY
INDICATOR
USB
OUTPUT
3A USB
OUTPUT
6.

OPERATING INSTRUCTIONS

IMPORTANT! Charge immediately after purchase and when battery level is below 40%, to keep the internal battery fully charged and prolong battery life.
POWERING ON
Press the ON/OFF power switch. The unit will initialize, and all icons on the LCD screen will activate. If normal function is detected, the screen will return to its normal display.
CHECKING THE LEVEL OF THE INTERNAL BATTERY
The Battery Capacity Indicator on the LCD display will show the battery's charge level in 20-percent increments. For best performance, the battery capacity should be 20%
or greater.

CHARGING THE INTERNAL BATTERY

NOTE: Do not use the unit while charging its internal battery.
AC adaptor
1. If the AC Output LED is lit, press the AC button to turn off before charging.
2. Connect the provided AC charger to the AC input socket on the front of the unit. Plug the charger's power cord directly into a live grounded 120V outlet. Charging will
start automatically, and the
3. When the internal battery is fully charged, all five bars of the Battery Capacity
charging will take approximately 8 hours.
4. When the unit is fully charged, unplug the charger from the 120V outlet and then from the unit.
Solar Charging (60W panel not included)
1. If the 12V DC Output LED is lit, press the DC power button to turn off before charging.
2. Place the solar panel (not included) in direct sunlight. Do not expose the power station to direct sunlight or wet conditions.
3. Connect your 3.5mm solar panel output cable to the DC input port of the unit. Charging will start automatically, and the
indicators will flash.
4. When the internal battery is fully charged, all five bars of the Battery Capacity
charging will take approximately 7 hours.
5. When the unit is fully charged, unplug the solar panel from the unit.
POWERING A 12V DC DEVICE
NOTE: Do not power a 12V device while charging the internal battery.
12V DC Output
1. Make sure the device to be powered is OFF before inserting the 12V DC plug into one of the two 12V DC output ports.
2. Plug the 12V DC device into one of the 12V DC output ports and turn on the 12V DC device (if required). Press the DC button. The
Outlet and Power Output indicators will show on the display.
3. When finished, press the DC button, turn off the DC device (if required) and unplug from the DC output port.
4. Recharge the unit when the battery level is below 40%.
12V DC Cigarette Outlet plug
1. Make sure the device to be powered is OFF before inserting the 12V DC cigarette outlet plug into the 12V DC cigarette outlet socket.
2. Plug the 12V DC device into the DC cigarette outlet socket and turn on the 12V DC device (if required). Press the DC button. The
Outlet and Power Output indicators will show on the display.
3. When finished, press the DC button, turn off the DC device (if required) and unplug from the 12V DC Cigarette Outlet socket.
4. Recharge the unit when the battery level is below 40%.

USING THE USB PORTS

Three USB ports provide 2.4A at 5V DC and one
1. Plug the device into one of the USB ports on the front panel.
2. Press the USB power button.
3. Turn on the USB device, if necessary. The
4. When finished, press the USB power button, turn off the USB device (if required) and unplug from the USB port.
5. Recharge the unit when the battery level is below 40%.
12V DC 12V DC LIGHT
OUTPUT CIGARETTE
OUTLET
OUTPUT
Charging and the Battery Capacity
USB port provides 3A.
USB, USB and
WARNING
POWER OUTPUT
INDICATOR
AC OUTPUT
indicators will flash.
indicator on the display will show. After 10 seconds, the display will turn off. Complete
indicator on the display will show. After 10 seconds, the display will turn off. Complete
Power Output indicators will show on the display.
• 4 •
Charging and the Battery Capacity
12V DC output, 12V DC Cigarette
12V DC output, 12V DC Cigarette