WorkSmart 53603 Instructions De Montage

CHAISE à dOSSIER GRIllAGé AvEC ACCOUdOIRS
6
7R
8
9,11
9,10
4
9,11
9,10
3
1
Enlever toutes les pièces du carton, les organiser selon les numéros de pièce indiqués sur la liste et s'assurer que les quantités des
pièces reçues sont correctes.
éTAPE 1 Insérer les cinq roulettes (2) dans la base (1) et pousser fort jusqu'à ce que chaque roulette (2) s'encliquette. Insérer le vérin
pneumatique avec couvercle (3) dans la base (1).
éTAPE 2 Attacher la plaque du siège (4) au coussin du siège (5) avec la flèche orientée vers l'avant du fauteuil en utilisant deux rondelles
plates (9) et deux vis longues (10) sur l'avant de la plaque du siège (4) et deux rondelles plates (9) et deux vis courtes (11) sur l'arrière de la
plaque du siège (4). RESSERRER COMPLÈTEMENT LES QUATRE VIS.
éTAPE 3 Aligner les trous dans les bras (7L et 7R) sur les trous sur le dessous du coussin du siège (5). En utilisant trois rondelles plates (9) et
trois vis longues (10) pour chaque bras, attacher les bras (7L et 7R) au coussin du siège (5). RESSERRER COMPLÈTEMENT TOUTES LES VIS.
éTAPE 4 Poser le support du dossier (8) sur la plaque du siège (4) et l'attacher au coussin du siège (5) en utilisant quatre rondelles plates (9)
et trois vis courtes (11) COMME MONTRÉ DANS LE DESSIN DÉTAILLÉ A. RESSERRER COMPLÈTEMENT LES VIS.
éTAPE 5 Placer le siège assemblé sur le dessus du vérin pneumatique (3) et pousser la pression vers le bas.
ATTENTION : véRIFIER QUE TOUS lES vIS SONT INSTAlléS ET BIEN SERRéS AvANT dE l'UTIlISER.
53603
INSTRUCTIONS dE MONTAGE
dESSIN A: Assembler le support du
dossier (8) et la plaque du siège (4).
7l
5
9,10
9,11
PIèCE
1. Base . . . . . . . . . . . . . . . . . . . . 1
2. Roulettes . . . . . . . . . . . . . . . . . 5
9,10
3. Vérin pneumatique avec
couvercle . . . . . . . . . . . . . . . . . . . 1
4. Plaque du siège . . . . . . . . . . . . 1
5. Coussin du siège . . . . . . . . . . . 1
6. Coussin du dossier . . . . . . . . . 1
7. Bras gauche (7L) et droit (7R) . 2
8. Support du dossier
(installé à l'avance) . . . . . . . . . 1
9. Rondelle plate . . . . . . . . . . . . 14
10. Vis longue . . . . . . . . . . . . . . . 8
11. Vis courte . . . . . . . . . . . . . . . . 6
12. Clé Allen . . . . . . . . . . . . . . . . 1
2
11
9
4
8
QTé
LIMITED WarranTy
Work Smart chairs are warranted from the date of purchase against failure due to material and workmanship as follows:
• 15 Years on all non-moving metal parts.
• 5 Years on component parts including Control mechanisms, pneumatic cylinders, wood, plastic parts, base and casters.
• 3 Years on upholstery fabric and foam against wear and deterioration.
To make a warranty claim, contact Parts Department. Provide model number, proof of purchase, description of the problem and
obtain return authorization. At it's option Office Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer's component. The customer must prepay freight on any components returned to the factory. Return
freight on components still in warranty will be paid by Office Star Products.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons weighing 250 lbs. or
less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or any other
event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damages is excluded. The user assumes all risk of injury resulting from use of this product. When usage is more than 40 hours per week, a two
year warranty on all parts applies. Fabric and foam is warranted for one year. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts
are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail
parts@officestar.net, by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00
p.m. Pacific Time.
© Office Star Products Juin 2012
53603
SCREEN BACK CHAIR W/ ARMS
OPERATING INSTRUCTIONS
FEaTUrES
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift
lever (1). To lower seat height sit on chair and
lift lever (1).
NOTE: It is normal for chair to slightly lower under
body weight.
• LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of the
tilting feature. Turn knob (2) clockwise to increase tension and
counter-clockwise to decrease or ease the tension. To lock return
chair to the upright position and push lever (1) in. To unlock pull
lever (1) out.
NOTE: Be careful not to loosen the back tilt adjustment
knob completely.
WarnInG
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and knobs are
securely tightened.
3. Check that all bolts screws and knobs are tight every three
months or as needed.
4. Do not overturn back tilt knob when decreasing tension.
5. Dispose of packing material properly. Do not use plastic cover as
head covering. It may cause suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.