Assembly & Use Of The Pitcher - ninja Kitchen BL610C Série Guide D'utilisation

ASSEMBLY & USE OF THE PITCHER
ASSEMBLY
1 Place the motor base on a clean, dry, level
surface such as a counter or table top.
Press down on the motor base to make
sure that the suction cups adhere to the
counter or tabletop.
3 Align and lower the pitcher onto the
motor base. Handle should be aligned
slightly to the right of the LOCK symbol
on the motor base.
4 Rotate the pitcher clockwise until it clicks
in place. As the pitcher rotates, it will lower
and the safety tabs on the bottom of the
pitcher will slide under the safety tabs on
the top of the motor base.
5 The pitcher can be placed on the motor AUTO AUTO FROZEN DRINKS
AUTO BLEND BOISSONS CONGELÉES SMOOTHIES BLEND AUTO
MÉLANGE MÉLANGE
AUTO AUTO
AUTO ON / OFF 1200 ULTRA BLEND PURÉE D' ALIMENTS FOOD PURÉE ON / OFF 1200 AUTO
PURÉE D' ALIMENTS FOOD PURÉE MARCHE WATTS ULTRA MÉLANGE MARCHE /ARRÊT WATTS ULTRA BLEND ULTRA MÉLANGE
/ARRÊT
HIGH PULSE AUTO LOW / DOUGH MEDIUM HIGH AUTO
LOW / DOUGH BAS / PÂTE MOYEN MEDIUM ÉLEVÉ IMPULSION BAS / PÂTE MOYEN ÉLEVÉ IMPULSION PULSE
base two ways; the handle can be on the
front right corner or the front left corner.
10
ninjakitchen.com
6 Holding the Stacked Blade Assembly by
the top of the shaft, place it onto the drive
gear inside the pitcher. Ensure the blade
assembly is seated properly and is standing
upright.
NOTE: The blade assembly will fit loosely
on the drive gear.
7 Add ingredients to the pitcher, making sure
they do not exceed the highest measured
marking line on the side of the pitcher.
NOTE: Add liquid ingredients first and then
dry ingredients. DO NOT exceed the MAX
LIQUID mark (64 oz.) on the pitcher.
NOTE: When blending any kind of liquids,
such as drinks or smoothies, do not
exceed the MAX LIQUID mark (64 oz.)
on the pitcher.
NOTE: If you need to add additional
ingredients while the blender is running,
open the pour spout cap and pour the
ingredients in through the opening.
8 Holding the lid by the handle in the upright
position, place it on top of the pitcher,
aligning the triangle ( ) located on the
lid with the triangle ( ) located on the
pitcher's handle. Press the handle down
until you hear a click. The triangles on the
lid and pitcher handle MUST be aligned for
the blender to turn on.
9 Plug the power cord into an electrical
outlet and press the power button ( ).
10 Select the speed according to your
blending requirements*:
• Use the LOW setting for processing
and mixing.
• Use the MEDIUM setting for blending
and ice crushing.
• Use the HIGH setting for pureeing
and liquefying.
• Use the PULSE button for controlled
chopping and processing.
*See Blending Chart.
NOTE: Pulse ingredients for even
chopping by pressing the PULSE button
in short intervals.
11 When ingredients have reached your
desired consistency, stop the blender
by pressing the power button ( ) then
wait for the blade to stop turning.
12 Turn the pitcher counterclockwise, then
lift it up and off the base.
13a Open the pour spout cap and use
the spout to empty liquid contents.
13b For thicker consistencies, first
remove the lid. Press the release button
on the lid, pull the handle up to a 90
degree angle, then lift lid off the pitcher.
Carefully remove the blade assembly by
the top of the shaft. Place blade assembly
away from the work area to avoid
accidental contact. Empty contents from
the pitcher.
14 Unplug the motor base when unit is not
in use. To release the motor base from
the counter or tabletop, place your hands
underneath both sides of the motor
base and gently pull the unit up and
toward you.
ninjakitchen.com
11