Publicité
50081
- This product is not a toy. This prod-
DC Power Pack
uct is not for children under 8 years
of age.
- Save the supplied instructions and
THE PROGRAM
packaging.
To connect this power pack to your
Preparation
layout, we recommend:
Connect the power pack to the layout
- 10152 Insulated Track, Double,
using the red and blue terminals on
150 mm (equipped with terminals)
- 50160 Track Power Cable
the rear of the power pack. Push
each terminal inward slightly. Insert
the connecting wire into the hole on
If your layout also requires AC power
the top of the terminal.
for accessories, we recommend:
- 51081 AC Transformer, 0.5 Amp,
Plug the power pack cord into a
house current outlet.
18 Volt, 120 Volt
For information on the complete LGB
Speed/Direction Control
program, see the LGB catalog.
The knob on the face of the power
pack is a combination speed and
direction control.
OPERATION
When the knob is in the "center off"
position, the locomotive will stop.
CAUTION! Safety advice:
Turn the knob to the right, and the
- This power supply should be
loco will travel in one direction. Turn
inspected regularly for possible
the knob to the left, and the loco will
dangers, such as damage to the
travel in the opposite direction. The
cables, plugs or housing. If damage
further you turn the knob, right or
is found, do not use this power
left, the faster the loco will travel.
supply. The house current cable
cannot be replaced.
Multi-Train System
- Disconnect this power supply from
This power pack can be used with
house current before cleaning the
the
LGB
housing.
However, it will only provide enough
- Disconnect this power supply from
power to operate one or two locomo-
house current if there is a short cir-
cuit or overload. Remove the short
tives at the same time. The actual
number of locos you can operate
circuit or overload before connect-
depends on the power requirements
ing the power supply again.
of those locos.
- This power supply is for indoor use
only. Keep it away from moisture.
To use this power pack with the
Multi-Train System, connect the
Do not install it in an enclosed
power pack to the Central Station.
space.
Turn the speed/direction control to
- Install the transformer on a firm
surface.
the highest position (4) and plug the
power pack cord into a house current
- Do not insert the track power cable
outlet.
into a house current outlet.
EXTREME DANGER!
- Do not connect the toy to more
Overload Protection
This power pack is equipped with
than one power supply.
primary and secondary overload pro-
- This power supply is for use with
tection against short circuits and
LGB and LEHMANN products only.
3
overheating. If the power pack is
overloaded, this device will turn the
power pack off.
If this happens, unplug the power
pack cord from the house current
outlet immediately:
1. Short circuits: Find and remove
the short circuit. Reconnect the
power pack cord.
2. Overheating: Wait several minutes
for the power pack to cool.
Reconnect the power pack cord.
Operate fewer locomotives with
the power pack.
Multi-Train
System.
4
51081
Preparation
AC Transformer
Connect the black and white wires
according to the instructions provid-
ed with the powered accessory prod-
THE PROGRAM
uct. Plug the transformer into a
This transformer can be used with
house current outlet.
most LGB products that require AC
Overload Protection
power, including:
This transformer is equipped with
- Electric switches and signals (using
51750 or 17100 control)
overload protection against short cir-
cuits and overheating. If the trans-
- 10560 Electric Uncoupler
former is overloaded, this device will
- 50500 Street Light
turn the transformer off.
- 51750 EPL Control Box
- 51800 On/Off Control Box
If this happens, unplug the trans-
former from the house current outlet
For information on the complete LGB
immediately:
program, see the LGB catalog.
1. Short circuits: Find and remove
the short circuit. Reconnect the
transformer.
OPERATION
2. Overheating: Wait several minutes
for the transformer to cool. Then
CAUTION! Safety advice:
continue operation with fewer
- This power supply should be
accessories.
inspected regularly for possible
dangers, such as damage to the
housing. If damage is found, do not
use this power supply.
- Disconnect this power supply from
house current before cleaning the
housing.
- Disconnect this power supply from
house current if there is a short cir-
cuit or overload. Remove the short
circuit or overload before connect-
ing the power supply again.
- This power supply is for indoor use
only. Keep it away from moisture.
Do not install it in an enclosed
space.
- Do not insert the black and white
cable into a house current outlet.
EXTREME DANGER!
- Do not connect the toy to more
than one power supply.
- This power supply is for use with
LGB and LEHMANN products only.
- This product is not a toy. This prod-
uct is not for children under 8 years
of age.
- Save the supplied instructions and
packaging.
5
Publicité
