FAME MS 5004 Manuel D'utilisation page 6

Important Safety Instructions!
Please read before connection and operation!
This product has left the manufactory in a safe and operational
condition. In order to retain this condition and to ensure for
safe operation, please adhere to the following recommenda-
tions and warnings found in this manual.
WARNING: In order to prevent the risk of fi re or electrocu-
tion, this device must not be exposed to moisture or rain.
Do not remove or open the housing – there are no compo-
nents in the interior which are serviceable by the user.
This Symbol, wherever it appears, warns of any
dangerous, non-isolated voltage within the housing
– voltage which may be dangerous and cause
electrocution.
This Symbol, wherever it appears, warns of any exter-
nally accessible, dangerous voltage. Every connection
made with a connecting terminal, which features this
symbol, must only be made with cables recommended
by the manufacturer or those installed by properly trained
personnel.
This Symbol, wherever it appears, alerts to import-
ant operating and maintenance instructions, which
can be found in the included documents. Please
read the hand-book.
This Symbol, wherever it appears, warns of: Cauti-
on! Hot Surface! Do not touch to prevent burns.
• Please read these instructions
• Please keep these instructions in a safe place.
• Follow all warnings and instructions on
the device and in this manual.
• Do not operate this device near water. Do not pla-
ce this device near water, bath tubs, sinks, moist
areas, swimming pools or in damp rooms.
• Do not place any vessels containing liquids such as
drinking glasses, vases, bottles etc. on the device.
• Clean the device only with a dry cloth.
• Do not remove any part or component of the housing.
• The operating voltage displayed on the device must match
the voltage of the local mains power supply. If you are not
sure about the voltage of your local mains power supply
please refer to your distributor or local power supplier.
• To prevent the risk of electrocution, the grounding of the
device must be maintained. Use only the included power
supply connection cable and keep the function of the
side, grounded contacts of the mains connection upright.
Ensure that the device is connected only to mains sockets
which feature a properly functioning protective earth.
• Protect the power supply cable from being walked on
and crushed, especially near the plug, socket – and
where it exits the device! Power supply cables should
always be handled with care. Inspect the cable in
regular intervals for wear and tear, especially near the
plug, socket and at the connection with the device.
• Never use a damaged power supply cable.
• Disconnect the cable from the device during thunder-
storms and when not in use for long periods of time.
• The device is completely removed from the mains
power supply only when the cable has been disconnec-
ted. The device should positioned in such a way as to
allow for quick and easy disconnection of the cable.
6
• Fuse: replace fuses only with the type IEC 127 (5x20mm) and
the correct nominal value, to ensure optimal performance!
Do not use shorted fuses or bridge the fuse holder. Fuses
should only be replaced by properly trained personnel.
• All maintenance should be done by qualifi ed per-
sonnel. Maintenance is required if the device has
been damaged in any wax, for example:
> If the power supply cable or the plug is
damaged or shows sign of wear.
> If fl uids of objects get into the housing
> If the device is exposed to rain or moisture.
> If the device does not operate normally, although the
instructions of the user's manual were followed.
> If the device was dropped or the
housing has been damaged.
• Devices connected to these amplifi ers should not fall below
the minimum nominal impedance printed in this manual
or the device itself. The cables used must be in accordance
with the local regulations have a suffi cient diameter.
• Keep this device out of direct sunlight.
• Do not position this device near sources of heat such as
radiators, cookers or other device that produce heat.
• Do not block the ventilation openings of the housing.
Install this device only as instructed by the manufacturer.
This device my not be installed – for example in a rack,
except in the case that suffi cient ventilation is provided.
• A cold device should always be allowed to warm up
to the temperature of its environment, when trans-
ported to a new location. Condensation may have
formed in the interior of the housing which may cause
damage to the device if not allowed to warm up.
• Do not expose to or place any open fl ames,
such as burning candles, on the device.
• The device should be positioned at
least 20 cm from any wall.
• The device may only be used together with trolleys, stands,
tables or mounts which are specifi cally from the manufactu-
rer or were sold together with the device. If a trolley is used,
be careful to prevent potential injuries caused by tipping.
• Use only accessories recommended by the manufac-
turer. This applies to all kinds of accessories, such as
protective covers, transport bags, stands as well as
wall ceiling mounts. Always follow the manufacturer's
instructions when using accessories. Always use the
mounting points intended by the manufacturer only.
• This device is not suited for persons (including child-
ren) with physical, sensory or mental handicaps, or for
persons with insuffi cient experience and/or knowled-
ge to operate such a device. Children under the age
4 should be kept out of reach of this device.
• Do not put any objects through the ventilation
openings of the housing, this may cause dange-
rous, electric components to be damaged or shor-
ted. This may result in fi re or electrocution.
• This device is capable of producing sonic pressure levels
of more than 90dB. This may result in permanent hearing
damage! Hearing protection should be worn if exposed to
high sonic pressure levels for extended periods of time.
• The manufacturer guarantees the safety, reliability and per-
formance of this device under the following circumstances:
> Installation, expansion, reinstallation, modi-
fi cation and repairs were carried out by the
manufacturer or authorized personnel.