Using The Filter Function (Filter Section); Selecting The Crossfader's Curve Characteristics (Crossfader Section); Starting Playback Of A Pioneer Dj Player Using The Fader (Fader Start Section) - Pioneer DJM-250-K Mode D'emploi

3 Move the crossfader f gradually towards the right.
While checking the sound output from the speakers, operate the cross-
fader to substitute the sound of [CH-1] with the sound of [CH-2].
Mixing is completed once only the [CH-2] sound is being output from the
speakers.
Using the filter function (filter
section)
g
SOUND COLOR FILTER
1
LPF HPF
h
Each channel is equipped with a SOUND COLOR FILTER function by
which filter effects can be achieved simply by turning a large control.
The treble or bass sound can be removed by turning the
[SOUND COLOR FILTER] control h.
Turn the [CH-1] 1 or [CH-2] 2 [SOUND COLOR FILTER]
control h.
The effect is applied to the sound and the indicator's color changes.
The effect type and indicator color differs according to the direction in
which the [FILTER] control is turned, as shown on the table below.
Direction of
Description of effect
rotation
Applies the effect of the
Left treble sound fading out.
(LPF: low pass filter)
Center —
Applies the effect of the bass
Right sound fading out.
(HPF: high pass filter)
Mixing using the SOUND COLOR FILTER
control
Prepare the unit in advance so that the sound of [CH-1] 1 is being out-
put from the speakers. For instructions on preparation, see Outputting
sound on page 10.
For instructions on monitoring the sound, see Monitoring the sound over
headphones (headphones section) on page 12.
1 Operate the crossfader and [CH-2] 2.
Operate as described in steps 2 to 6 under Mixing using the channel
faders on page 10.
2 Turn the [CH-2] 2 [SOUND COLOR FILTER] control h
fully clockwise.
3 Move the [CH-2] 2 channel fader e away from you.
4 While turning the [CH-1] 1 [SOUND COLOR FILTER]
control h counterclockwise from the center, turn the
[CH-2] 2 [SOUND COLOR FILTER] control h towards the
center.
While checking the sound output from the speakers, operate the
[SOUND COLOR FILTER] controls h and replace the [CH-1] and [CH-2]
sound.
Move the [CH-1] 1 channel fader e towards the front. Mixing is com-
pleted once only the sound of [CH-2] is output from the speakers.
Selecting the crossfader's curve
characteristics (crossfader section)
— [THRU]: Choose this when you do not want to use the crossfader.
2
— [
LPF HPF
— [
h
moves away from either the left or right edge, the sound is immedi-
ately output from the opposite side.)
Starting playback of a Pioneer DJ
player using the fader (fader start
section)
Indicator
If you connect a Pioneer DJ player using a control cable (supplied with
Red (flashing)
a DJ player), you can start playback of control other operations of the DJ
player with the fader of this unit.
Orange (lit)
The fader start function can only be used when connected to a Pioneer
DJ player.
Green (flashing)
Connect this unit and Pioneer DJ player beforehand. For instructions on
connections, see Connecting the input/output terminals on page 6.
To start playback using the channel
faders
1 Set [THRU,
switch) j to [THRU].
2 Press the [CH-1] or [CH-2] button i in the fader start
section.
Turn the fader start function on.
3 Move the channel fader e to the very front.
4 Set the cue on the DJ player.
The DJ player pauses playback at the cue point.
5 Move the channel fader e away from you.
Playback starts on the DJ player.
! If you set the channel fader back to the original position, the player
instantaneously returns to the cue point already set and pauses
playback (back cue).
CROSS FADER
THRU
j
]: Set here for a curve that rises gradually.
]: Set here for a curve that rises steeply. (When the crossfader
FADER START
CH-1 CH-2
i
, ] (the crossfader curve selector
11
En