EINHELL Kreta Instructions De Montage Et Mode D'emploi page 13

Anleitung Grillküche Kreta Rho
4 x 10 mm self-tapping screws and additionally
fasten to the side of the stand (3) and chassis (4)
using two M6 x 35 lock bolts, washers and
hexagonal nuts.
(Fig. 3) Applies to Kreta only: Place the
preassembled frame unit on the ground upside down
and simultaneously pull the front cover (1) on both
tubular legs up to the height of the fittings holder.
(Fig. 4) Fasten the tray plate (1) to the tubular frame
using 8 M6 x 35 lock bolts, washers and hexagonal
nuts. Refer to detail A.
(Fig. 5) Insert a size 10x85 screw through the tubular
leg from the inside and screw on a size M10 nut from
the outside and tighten. Then slide the wheel on the
screw and screw on a size M10 self-locking nut with
plastic insert. Then mount the wheel cover (5).
(Fig. 6) Connect the control knob (1) to the control
axle.
(Fig. 7) Fasten the handle (1) to the grill hood (2) by
inserting the M6 x 70 screw (3) through the handle
(1) and the spacer (5). Place a grommet (6) between
the spacer (5) and the grill hood (2) and a second
grommet (6) between the grill hood (2) and the
hexagonal nut (7). Refer to detail B.
(Fig. 8) Insert the ignition electrode (1) into the
bottom of the ignition panel (2) and mount it in the
grill bottom (3) using the M4 x 10 bolt and hexagonal
nut.
(Fig. 9) Fasten the grill bottom (1) to the back of the
lateral cross struts (2) with the hinges using
M6 x 45 lock bolts (3), grommets (4) and hexagonal
nuts (5). Do not tighten the bolts too much so as to
avoid damaging the paint on the grill bottom.
IMPORTANT: The grommets must be positioned
between cross strut/grill bottom and hexagonal
nut/grill bottom.
(Fig. 10) Connect the bracket (1) on the grease
collecting pan by inserting it into the respective hole
(2) on the inside of the grill bottom (3).
(Fig. 11) Install the burner (2) by lowering in into the
grill bottom (1) and fastening it at the bottom with two
4 x 10 screws (3). Ensure that the gas nozzle (4)
attached to the control fitting is seated at the center
of the burner tube (5) as shown in detail D.
(Fig. 12) Fasten the hinge bracket (1) to the grill
hood (5) using M6 x 15 lock bolts (2), grommets (3)
and hexagonal nuts (4). Do not tighten the bolts too
15.12.2003 13:03 Uhr
much so as to avoid damaging the paint on the grill
hood.
IMPORTANT: The grommets must be positioned
between hinge/grill hood and hexagonal nut/grill
hood.
Fasten the hinges (6) to the grill bottom (7) using the
M6 x 15 lock bolts (2), grommets (3) and hexagonal
nuts (4). Do not tighten the bolts too much so as to
avoid damaging the paint on the grill bottom.
IMPORTANT: The grommets must be positioned
between hinge/grill bottom and hexagonal nut/grill
bottom. Refer to detail C.
(Fig. 13) Connect the ignition cable (1) to the ignition
button (2). Ensure that the ignition cable is kept away
from the hot areas of the grill.
(Fig. 14) Place the lava rock grate (1) in the grill
bottom (2) and evenly distribute the lava rocks over
the top. Place the griddle (3) on the grill bottom (2).
Attach the warming rack (4) by separately inserting
the wire brace and the wire angle into the holes on
the right side of the grill hood and the grill bottom.
Now attach the left side of the warming rack in the
same way.
Important! Carefully mount the warming rack so as
to avoid damaging the surface of the grill.
Important! Wash the griddle and the warming rack
with a lukewarm soap solution prior to starting up the
unit. Thoroughly rinse with water and dry.
(Fig. 15) Fasten the side trays (1) to the tubular
frame (2) using 2 M6 x 35 mm bolts and hexagonal
nuts each.
(Fig. 16) Applies to Rhodos only: Fasten bottom,
front cover (1) to the tubular frame using 4 x 10
screws (2).
(Fig. 17) Applies to Rhodos only: Fasten top, front
cover (1) to the tubular frame using 4 x 10 screws
(2).
(Fig. 18) Applies to Rhodos only: Attach wire
basket to the tubular frame.
Connecting the gas bottle
The following parts are needed to connect up the
barbecue:
A standard camping gas bottle of 5 - 11 kg filling
b
Seite 13
GB
13