Lock Instructions - SentrySafe EF3025E Manuel D'utilisation

Lock instructions

Gaining Entry into Safes with Combination Locks
1
3-Number Combination Lock
and Dual Combination Key Lock
NOTE: See the sticker on the back cover of
this manual for your combination.
IMPORTANT: The lock on this safe is
in the open position. DO NOT operate
the combination until first reading and
understanding the following instructions.
2
Gaining Entry into Safes with Electronic Locks
Standard Electronic Lock and
Dual Electronic Key Lock
To activate lock:
Four alkaline AA batteries, Voltage: 6Vdc, (not
included) are required to activate the keypad.
NOTE: Non-alkaline and rechargeable
batteries ARE NOT RECOMMENDED.
To install batteries:
A
B
its wires. This will expose the battery holder.
(Fig. B)
3. Install four alkaline AA batteries as illustrated on
the back of the battery holder.
4. Reconnect the keypad by inserting the keypad's
four posts into the matching holes.
5. Push down to snap into place.
WITH DOOR OPEN!
Test your combination several times
To unlock and open
Before dialing your combination, simply insert the
key (if equipped) in the lock and turn clockwise.
1. Start the dial at ZERO.
2. Turn the dial to the left. Make sure ZERO
passes the pointer at least THREE times. Then
WITH DOOR OPEN!
(See back cover of this manual for your
Test your factory code several times with the door
open.
NOTE: Only a light touch is needed. A green
PROCEED light and a single beep indicate
that the keypad "felt" your touch. The
lock allows 5 seconds for each key press.
If you pause longer, an error signal will
occur (blinking red light and three beeps),
indicating you should start over.
For safes with dual combination key lock insert key
and turn clockwise.
1. Press the 5-digit factory code. The green light
will come on.
1. Using two
2. Turn the handle clockwise and open the door.
hands, hold the
keypad, thumbs
Access codes
down, on its
There are three possible ways to unlock and
left and right
access the safe—by entering its preset Factory
sides. Push up
Code, your own User Code or a User PIN (Personal
the keypad with
Identification Number).
your thumbs,
and disconnect it
You can always open the safe by entering the
from the safe by
5-digit Factory Code. This code cannot be deleted.
pulling it towards
But if you prefer to use your own code, you can
you. (Fig. A)
program the safe to open to the 5-digit User Code
2. Let the
of your choice. If you wish to give someone else
disengaged
temporary access to the safe, you can program a
keypad hang by
User PIN that can later be erased.
Programming a user code
There are two ways to program a user code.
A 1. Press the Program key. (Prog.)
2. Enter the Factory Code. The green LED remains
ON while you enter the 5-digit user code of your
choice. After 5 digits are entered the green LED
turns OFF.
(To enter a new User Code, repeat these steps.)
Test first
with the door open.
Test first
factory code.)
4
stop at the first number of your combination.
3. Turn the dial to the right. Stop the
SECOND time you reach the second number of
your combination.
4. Turn the dial to the left. Stop the FIRST
time the pointer reaches the third number of your
combination.
To Close and Lock
With the door closed, turn the handle
counterclockwise to secure the locking bolts, then
spin the combination dial to the left at least four
times to scramble the combination.
B 1. Press the red button on inside of door (hinge
side). The lock will "beep" and the green LED will
come on.
2. Enter a 5-digit user code.
(To enter a new User Code, repeat these steps.)
Keep your new user code secure
For your records, please copy it here:
_____ _____ _____ _____ _____
Programming a user PIN
1. Press the Program key.
2. Press it a second time.
3. Enter your 5-digit User Code. The green LED
remains ON.
4. Enter the 5-digit User PIN of your choice (any
combination except 00000.) After 5 digits are
entered, the green LED turns OFF.
(To enter a new User PIN, repeat these steps. To
erase the User PIN, press Program twice, enter your
User Code and then enter 00000.)
Key override
If your electronic lock fails or you do not have any
codes available, you may use a key override to
access this unit.
1. Using two hands, hold the keypad, thumbs
down, on its left and right sides. Push up the
keypad with your thumbs, disconnect and remove
the battery holder.
2. Insert the skeleton key into the key hole inside
the opening for the battery.
3. Turn the key to the right.
4. Open the door.