BH HIPOWER LK G815 Instructions De Montage Et Utilisation page 13

4. FITTING THE MAIN POST.-
Next, bring the main post (97) up to boss on the main
body (1), Fig.7.
Slip the main post (97) over the boss on the main body
(1) in the direction of the arrow, Fig.7, making sure not to
snag any of the cables.
Refit the screws (98) (99), the washers (100)(101) Fig.7,
and tighten securely.
Connect the terminals (208) and (209), Fig.8.
Insert the left bottom post cover (155) and the right
bottom post cover (155-1) and tighten securely with (161)
screws in the direction of the arrow, Fig.8.
5. FITTING THE MONITOR.-
Next, connect terminals (208), sticking out of the
handlebar (97), and terminal (B), sticking out of the
monitor (169), Fig.9.
Place the monitor (169) on top of the plate on the main
post (97), as shown in Fig.9, making sure not to pinch the
wires.
Use screws (125) to hold the monitor in place, Fig.9.
Place the rear monitor cover (164) and the front cover
(165) with screws (167).
Take the left handlebar (225), and slot itinto position as
shown in Fig.9 by lining up the holes.
Fit the screws (232) safety washer (230)
and flat washers (231) and tighten them securely.
Then place the cover (163) take the screw (167) and
tighten it.
Make the same with the right handlebar (224).
6. FITTING THE FOCUS BARS.-
Insert the left focus bar (108) (marked with the letter "L")
onto the focus bar spindle Fig.10, fit the washered bolts
(119) and the flat washers (120) and (123) and with the
help of the box spanners tighten securely.
Take the right focus bar (107), (marked with the letter "R")
and go through the same assembly procedure as with the
left.
7. FITTING THE FOOT STRAP.-
Fit the foot strap (129) and position it with the lower focus
bar (108) as shown in Fig.11, lining up the holes.
Next, insert the bolt (139) and tighten using nut (132).
Fit the foot strap (130) and position it with the lower focus
bar (107) as shown in Fig.11, lining up the holes.
Next, insert the bolt (139) and tighten using nut (132).
8. FITTING THE UPPER FOCUS BARS.-
Once you have assembled the top focus bars, take the
lower focus bar (110) (marked with the letter "L") and
insert it onto the boss for the top bar, Fig.12, lining up the
holes for the screws.
Fit the bolts (121); and cap nuts (122) and tighten
securely.
Go through the same procedure for the lower right focus
bar (111) (marked with the letter "R").
9. FITTING THE FOCUS BAR SPINDLE
COVERS.-
Take the front (150) and rear (151) covers and position
them on the main post (107), Fig.13. Now use the screws
(156) to attach them to the post.
Take the front (150) and rear (151) covers and position
them on the main post (108), Fig.13. Now use the screws
(156) to attach them to the post.
10. FITTING THE FOCUS BAR SIDE
COVERS TO THE FOOT BARS.-
Take the covers (152 and 153), marked on the inside with
the letter "R", and position them at the end of the foot bars
with the inside of the focus bars on the right hand side, as
shown in Fig.14. Now use screws (157) to attach them.
Carry out the same procedure using the covers (152 and
153) marked on the inside with the letter "L".
Take the cover (146), marked on the inside with the letter
"R", and position them at the spindle end with the bars on
the right hand side, as shown in Fig.14. Now use screws
(157) to attach them.
Carry out the same procedure at the other end of the bar
using the covers (146) marked on the inside with the letter
"L" Fig.15.
11. FITTING THE FOOT RESTS.-
Position the left footrest (154) (marked with the letter "L")
on top of the unit's left foot (129), Fig.16, (left and right
refers to the user's position doing exercise) fit screws
(159) and washers (158) and tighten.
Next, position the right footrest (154) (marked with the
letter "R") on top of the right foot (130) and secure using
screws (159) and washers (158).
12. FITTING THE BOTTLE HOLDER.-
Remove screws (161) and washers (162) located on the
main post (97) and fiit the bottle holder (220) and suport
(222) Fig.18, using the same screws (161) and washers
(162).
LEVELLING.-
Once the unit has been placed into its final position, make
sure that it sits flat on the floor and that it is level. This can
be achieved by screwing the adjustable feet (61) up or
down, as shown in Fig.18.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (223), as shown in
Fig.19, which make it easier to move. The two wheels at
the front of the unit make it easier to place the unit in to
any chosen position by lifting the rear slightly
Store your unit in a dry place, preferably not subject to
changes in temperature.
MAINS CONNECTION.-
Insert the jack (m) for the transformer into the connection
hole on the main body (k) (bottom, rear of the machine)
and then plug the transformer (221) into a 230 V mains
supply, Fig.20.
13
MOD. G815