Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
NOTE: For initial setup, a home/business Wi-Fi
internet connection will be required to complete
Step 1 through Step 3, and email configuration.
WELCOME
Globalstar Sat-Fi2.
Thank you for purchasing a
devices to run your business and your life even when cell service isn't available.
PRODUCT REQUIRES ACTIVATION
In order to begin using your Globalstar Sat-Fi2, please make
sure you have an active subscription. If you do not have an
active subscription or encounter issues with your device, please
visit ca.Globalstar.com/Sat-Fi2Support for assistance.
ACTIVATE YOUR SAT-FI2
MOBILE DIRECTORY NUMBER (MDN), AND ICCID
In order to activate your Sat-Fi2 and register your Globalstar My Account profile, you will need
to have access to the ICCID number, which can be found on the bottom of your Sat-Fi2. Your
MDN (telephone number) will be assigned to you during activation.
STEP 1: CHARGE YOUR SAT-FI2
Connect the Micro USB Data/Power Cable to the Sat-Fi2 USB
port and AC Adapter. Then connect the included AC adapter
to charge the Sat-Fi2 via the USB port. For best results, please
leave the Sat-Fi2 connected to the charger for at least 7 hours.
STEP 2: REGISTER YOUR ACCOUNT
1. To register your account, open the Welcome to Globalstar email from
message-noreply@globalstar.com and click on
2. Follow the on-screen instructions to register your account.
Now you can use your smart
Register Now
STEP 3: SETTING UP THE SAT-FI2 APP
1. On your iOS or Android device, download
and install the Sat-Fi2 App from either the
Apple App Store or Google Play Store.
2. Ensure your device has a LTE or Wi-Fi
connection and open the Sat-Fi2 App. The
App will require the downloading of internal
applications necessary for setup. Do not
close the Sat-Fi2 App during this process.
3. A WELCOME screen will be displayed, select
LET'S GET STARTED. Start the configuration
process by selecting QUICK START OR
ADVANCED SETUP and follow the on-screen
instructions (see Figure 1).
Wi-Fi and Password Information
• Default Sat-Fi Wi-Fi name:
satfi2_ <xxxxxx>
(where xxxxxx is the
last 6 digits of the ICCID)
satfi1234
• Default Wi-Fi Password:
NOTE: A new firmware update may be available upon activation. An ADVANCED SETUP profile with admin
privileges is required to check for and perform firmware updates. See User Guide for instructions on how to
make a user profile an admin.
STEP 4: TEST THE SAT-FI2 CONNECTION
Make a satellite call to test and confirm the Sat-Fi2 system is configured and operational.
1. With your device fully charged, go outside where Sat-Fi2 has a 360° clear view of the sky with
no obstructions (buildings, trees, etc.) and power on the Sat-Fi2 (see Figure 2). Ensure
co-located antenna is fully extended in an upright position (see Figure 3).
NOTE: The Sat-Fi2 can take up to 3 to 5 minutes to power on, boot up, and begin establishing a satellite/
gateway connection. All three LED's will sequentially blink green while powering on/booting up. Once the
Sat-Fi2 has booted up, the Satellite LED will blink RED until the Sat-Fi2is registered with a gateway. A GPS fix
is needed to register with the gateway.
2. Open the Sat-Fi2 App and verify that both the
Bar. If the icons are not displayed you may not have a clear view of the sky.
3. In the Application Menu select
4. Enter the telephone number you wish to call, or choose a contact, and select
FIGURE 1
iOS
and
icons are displayed on the Status
.
Android
.
Publicité
Table des Matières
