NightStick NSP-4608BC Mode D'emploi

Instruction Manual
NSP-4608BC
US PATENT 9,713,217
Please read these instructions before using this product. They include important safety
and operation information.
WARNINGS
y NOT FOR USE ABOVE HAZARDOUS LOCATIONS
y DO NOT use in explosive atmospheres, near fl ammable liquids, or where explosion
proof lamps are required.
y DO NOT use in the proximity of vehicles or equipment when there is a risk of fl ammable
liquids coming into contact with the fl ashlight.
y DO NOT expose the batteries to water or salt water, or allow the batteries to get wet.
y DO NOT store the batteries with metallic objects that may cause a short circuit.
y Immediately discontinue use of the batteries if they emit an unusual smell, feel hot,
change color, change shape or appear abnormal in any way.
y Keep out of the reach of children.
INSTALLING BATTERIES
y Unscrew the battery compartment door on the back of the headlamp.
y Insert the batteries per the outline inside the battery compartment. Observe the correct
polarity of the batteries.
y Close the battery door and fasten the battery compartment door screw.
y The headlamp is now ready for use.
OPERATION
THE NSP-4608BC HAS TWO BUTTONS THAT CONTROL LIGHT OUTPUT:
LIGHTING MODES
Pressing the Spotlight Button will turn on the spotlight. Pressing the Floodlight Button
will turn on the fl oodlight. Pressing both buttons will turn on both the Spotlight and the
Floodlight. This mode is called Dual-Light.
EACH BUTTON HAS TWO BRIGHTNESS SETTINGS
y High-brightness - Press the desired button once
y Low-brightness - Press the desired button a second time
y Pressing the same button a third time will turn that lighting mode off
BATTERY SHUT OFF MODE:
y Press and hold both switches at the same time for 3 seconds to enable or disable
battery shut off mode.
y After three seconds the light will fl ash on and off 1 time to confi rm a change in the
battery safe mode.
NOTE: The battery safe mode reverts to disabled when batteries are removed or fully
discharged.
THE NSP-4608BC HAS A TILT ADJUSTMENT FEATURE:
Simply adjust the tilt angle of the light to illuminate the desired area.
THE NSP-4608BC FITS ON ANY HARD HAT THAT HAS A HARD HAT LAMP
BRACKET ATTACHED:
NIGHTSTICK NS-HMC4 HEADLAMP BRACKET MOUNTING INSTRUCTIONS
y Ensure mounting surface is clean and oil-free (use alcohol wipe if needed)
y Prior to installing, determine mounting location that allows headlamp to fully tilt without
interfering with helmet brim.
y Remove adhesive backing.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
y Firmly press bracket into place up for 30 seconds with fl at side facing up (see image).
y While supporting mount, slide headlamp clip into bracket slot. (Note: adhesive reaches
peak strength in 24 hours)
TO ATTACH TO THE HARD HAT LAMP BRACKET
Slide the clip on the back of the NSP-4608BC into the slot on the top edge of the Hard
Hat Lamp Bracket and press down fi rmly until the clip is fully engaged into the bracket.
TO REMOVE FROM THE HARD HAT LAMP BRACKET
Grasp the NSP-4608BC and pull up until the clip slides out of the Hard Hat Lamp
Bracket.
WARRANTY
LIMITED LIFETIME WARRANTY
Bayco Products, Inc. warrants this product to be free from defects in workmanship
and materials for the original purchaser's lifetime. The Limited Lifetime Warranty includes
the LEDs, housing and lenses. Rechargeable batteries, chargers, switches, electronics
and included accessories are warranted for a period of two years with proof of purchase.
Normal wear and failures which are caused by accidents, misuse, abuse, faulty installation
and lightning damage are excluded.
We will repair or replace this product should we determine it to be defective. This is the
only warranty, expressed or implied, including any warranty of merchantability or fi tness
for a particular purpose.
For a complete copy of the warranty, go to www.baycoproducts.com/bayco-product-
support/warranties. Retain your receipt for proof of purchase.
Veuillez lire ces instructions avant d'utiliser ce produit. Elles comprennent des
informations importantes liées à la sécurité et à l'utilisation de ce produit.
AVERTISSEMENTS
y NE PAS UTILISER AU-DESSUS D'ENDROITS DANGEREUX.
y NE PAS utiliser ce produit dans une atmosphère explosive, à proximité de liquides
infl ammables, ou dans des endroits exigeant un éclairage antidéfl agrant.
y NE PAS utiliser ce produit à proximité de véhicules ou d'équipement quand des
liquides infl ammables pourraient entrer en contact avec la lampe torche.
y NE PAS exposer les batteries à l'eau ou à l'eau salée, et ne pas laisser les batteries
se mouiller.
y NE PAS ranger les batteries à proximité d'objets métalliques qui pourraient causer un
court-circuit.
y Arrêtez immédiatement d'utiliser les batteries si elles émettent une odeur inhabituelle,
sont brûlantes au toucher, changent de forme, ou en cas de toute autre anomalie.
y Ne pas laisser pas à la portée des enfants
INSTALLATION DES PILES
y Dévissez le couvercle du compartiment de la batterie à l'arrière du projecteur.
y Insérez les piles par le contour à l'intérieur du compartiment à piles. Respectez la
polarité des piles.
y Fermez la porte de la batterie et serrez la vis de la porte du compartiment à piles.
y Le projecteur est maintenant prêt à être utilisé.
FONCTIONNEMENT
MODES D'ÉCLAIRAGE
Si vous appuyez sur le bouton
l'éclairage concentré. Si vous appuyez sur le bouton projecteur d'illumination vous
allumez l'éclairage d'illumination. Si vous appuyez sur les deux boutons vous allumez les
deux modes d'éclairage. Ce mode s'appelle Éclairage double. Chaque bouton comporte
deux types de luminosité.
INS-NSP-4608BC-21
Mode d'emploi
NSP-4608BC
projecteur à faisceau concentré vous allumez