Texas A/S Lilli 340TG Manuel De L'utilisateur page 11

Never attempt to make any adjustments, while the
engine is running.
Use extreme caution when reversing or pulling the
machine backwards
Never operate the engine indoor or in areas with low
ventilation. The exhaustion from the engine contains
carbon monoxide. Failure to observe could result in
permanent injury or death.
Gasoline safety
Use extreme care in handling gasoline. Gasoline is
extremely flammable, and the fumes are explosive.
Serious personal injury can occur, when gasoline is
spilled on yourself or your clothes. Rinse your skin and
change clothes immediately!
Use only an approved gasoline container. Do not use
soft drink bottle or similar!
Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
Never refuel your machine indoors.
Let the engine cool down before refilling
Never fill the fuel tank to more than 2.5 cm below bottom
of filler in order to provide space for fuel to expansion.
After refueling, ensure that the cap tighten securely.
Never use the lock-function on the gasoline gun, when
refueling.
Do not smoke while refueling.
Never refuel inside a building or where gasoline fumes
may get in contact with an ignition source.
Keep gasoline and engine away from appliance, pilot
lights, barbecues, electric appliances, power tools, etc.
If the fuel tank has to be drained, this shall be done
outdoors
Maintenance and storage
The engine shall be stopped when carrying out
maintenance and cleaning operations, when changing
tools and when being transported by means other than
under its own power.
Check regularly that all bolts and nuts are tightened.
Retighten if necessary.
The engine must be completely cooled before storing
indoors or covered.
If the machine unused for a period of time, please refer
to the instructions in this manual.
Maintain or replace safety and instruction labels, as
necessary.
Only use original spare parts or accessories. If not
original parts or accessories is used, the liability is no
longer applied.
Replace faulty silencers.
Miscellaneous
The gears are delivered pre-greased. However, always
ensure they are well greased before each use.
The motor is not pre-filled with oil.
Factory-fitted control devices, such as the handle-
mounted clutch cable, must not be removed or exposed.
Only drain the fuel tank outdoors. Gasoline is extremely
flammable, and the fumes are explosive.
Ensure that the machine is properly secured when
transported on a flatbed etc.
Reduce the throttle during engine shutdown and close
the fuel valve.
Due to vibrations, it is recommended to take a break for
every 30 minuttes use to avoid fatique in your arms.
Assembly
Please follow the steps in figure:
(Actual model may vary from the illustration shown)
1. Box content
A. Tiller with blades
B. Upper handlebar
C. Clutch handle
D. Lower handlebars
E. Depth skid/support wheels
F. Throttle control (Lilli 340/360)
G. Panel (Lilli 345/365)
H. Side guards (Lilli 360/365)
I. Extension blades (Lilli 360/365)
2. Fit the lower handlebar section. Use the supplied
mountings and bolts. You can choose between 2
different heights of handlebar.
3. Fit the upper handle. Use the supplied assembly kit as
shown.
4. Mount the clutch handle and throttle control as shown on
the picture. Only Lilli 340/360.
5. Mount the clutch handle, panel and throttle control as
shown on the picture. Only Lilli 345/365.
6. Mount the side guards using the bolts and nuts supplied.
Note the side guard must go under the body frame.
7. Mount the extension blades using the cotter bolts and
pins. Only Lilli 360/365.
8. Mount the support wheels with the cotter bolt and pin.
9. The support wheels can be turned, so it works as a
depth skid. Depth can be adjusted.
Fill the engine with oil.
See changing the oil section for more details.
Clothing
When using the machine, wear close-fitting work clothes,
hard-wearing work gloves, ear defenders and non-slip boots
with steel toecaps.
Operating the tiller
Ensure the machine is placed on a level surface with the
support wheels lowered prior to start.
Remove all foreign objects from the work area before
using the machine. Stones, glass, branches and similar
items may damage the tiller. Also, check the bolts on the
tiller are tightened.
Start the motor as per the instructions below. Stand
clear of the machine's moving parts.
Never attempt to move the machine in any way other
than intended for normal use while the motor is running.
The tiller is designed for use in vegetable gardens and
flowerbeds. Ensure that you are familiar with these
instructions before operating the machine, in particular the
motor start and stop procedures.
Fig 10: To use the black clutch handle the red control stick
(A) must first be activated. By tilting the control stick to the
right or left side and then activate the black handle lever, the
tiller will move forward or backwards.
11