Garmin BC 35 Instructions D'installation page 3

Masquer les pouces Voir aussi pour BC 35:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 5
If you do not see video on the Garmin device at the preferred
installation location, move the transmitter to another location
and test it again.
4
Repeat steps 2–3 until the transmitter operates correctly.
5
Test the camera view by observing the video on the device.
6
If the camera does not provide the optimal view for your
vehicle, move it to another location and test it again.
7
Repeat steps 5–6 until the camera mounting location
provides the optimal view for your vehicle.
TIP: Make note of the camera orientation when you are
testing the camera view to ensure correct permanent
installation.
Mounting the Camera
Before you permanently mount the camera, you should test the
mounting location for the optimal view for your vehicle
the Camera and Transmitter Location, page
If you have already connected the camera to the bracket, you
must first disassemble it.
1
Place the bracket
in the mounting location.
2
Select an option:
• If you are mounting the bracket directly on the surface of
your vehicle, mark the locations of the two holes on the
bracket
.
• If you are installing the bracket on a license plate, remove
one of the license plate screws and clip the bracket onto
the license plate, aligning the hole on the bracket
the hole on the license plate.
3
Secure the bracket to the vehicle using either the included
self-tapping screws
or the license-plate screw you
removed in step 2
.
4
Place the camera in the bracket, and determine the best
place for the camera cable
5
Using an appropriate drill bit, drill a hole for the camera cable
to enter the vehicle.
6
Feed the camera cable through the hole and route it to the
transmitter location.
7
Secure the camera in the bracket using the included hex
bolts
.
8
Adjust the angle of the camera and tighten the hex bolts
using the included hex key.
9
Apply RV sealant around the cable where it enters the
vehicle (optional).
Installing the Transmitter
Before you permanently install the transmitter, you must test the
installation location for correct operation
and Transmitter Location, page
Installation Instructions
(Testing
2).
to enter the vehicle.
(Testing the Camera
2).
1
Secure the transmitter to the installation location using
hardware appropriate for the location, such as screws, bolts,
or cable ties.
The fuse holder located near the transmitter is not
waterproof. Installing the fuse holder in a location that is
exposed to the elements is not recommended.
2
Connect the camera and transmitter cables.
The connector between the camera and the transmitter is not
waterproof. If you make this connection in a location exposed
to the elements, you must make sure that the connection is
waterproof.
3
Connect the power cable
24 VDC power source, preferably a reverse lamp
solderless wire-splice connector (not included).
NOTE: Connecting the transmitter to an always-on
12-24 VDC source (such as a running lamp) instead of a
reverse lamp requires you to manually switch power to the
transmitter. The transmitter may drain your vehicle battery if it
is left on.
4
If you did not use a solderless wire-splice connector, solder
and heat-shrink the electrical connections to protect them
from the elements.
Pairing the Camera with a Garmin Navigation
Device
1
Turn on the compatible Garmin navigation device, and bring
it within 3 m (10 ft.) of the camera.
2
Select Apps > Rear View.
3
Select Add New Camera.
4
with
Follow the on-screen instructions.
Multiple Cameras
You can pair up to 4 wireless cameras with a compatible Garmin
device. For example, you can pair one backup camera installed
on the cab and a second backup camera installed on a trailer.
See the BC
35 Owner's Manual for information about pairing
multiple cameras.
Appendix
Getting the Owner's Manual
You can get the most recent owner's manual from the web.
1
Go to garmin.com/manuals/BC35.
2
View or download the full owner's manual in your preferred
format.
Specifications
Camera and transmitter input
voltage
Transmitter fuse
Camera and transmitter current
usage
Water rating (camera)
from the transmitter to a 12–
, using a
From 9 to 28 Vdc
500 mA, fast-blow
150 mA at 12 Vdc
IEC 60529 IPX7*
3

Publicité

Table des Matières
loading

Table des Matières