Télécharger Imprimer la page
Les langues disponibles

Les langues disponibles

Liens rapides

Installation
Instructions
Questions? Call
1-800-944-9044(US)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT –
instructions for local inspector's use.
IMPORTANT –
governing codes and ordinances.
Note to Installer –
instructions with the Consumer.
or
1-800-265-8352(Canada)
Save these
Observe all
Be sure to leave these
Over the Range
Microwave Oven
Note to Consumer –
instructions for future reference.
• Skill level – Installation of this appliance requires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
KEEP THESE INSTRUCTIONS
Keep these
READ CAREFULLY.
p/n 316495
162
A
pril
201
.
7
loading

Sommaire des Matières pour Frigidaire FFMV1745TB

  • Page 1 Installation Over the Range Instructions Microwave Oven Questions? Call 1-800-944-9044(US) 1-800-265-8352(Canada) BEFORE YOU BEGIN Note to Consumer – Read these instructions completely and carefully. • Keep these instructions for future reference. IMPORTANT – • Save these • Skill level – Installation of this appliance requires instructions for local inspector’s use.
  • Page 2 Installation Instructions Adapting Microwave Blower CONTENTS – for Outside Back Exhaust....17 18 General information Mount the Microwave Oven ....19 Important Safety Instructions ........3 Recirculating ........– Electrical Requirements .......... 3 Attach Mounting Plate to Wall .... Damage – Shipment/Installation......4 Preparation of Top Cabinet ....2 Parts Included............
  • Page 3 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit checked The installer must perform a ground continuity check by a qualified electrician to make sure the receptacle is properly grounded. on the power outlet box before beginning the installation to ensure that the outlet box is properly Where a standard two-prong wall receptacle is...
  • Page 4 Installation Instructions DAMAGE—SHIPMENT/ PARTS INCLUDED (CONT.) INSTALLATION ADDITIONAL PARTS PART QUANTITY • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair Cabinet or replacement. Template • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer.
  • Page 5 Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square # 1 Phillips screwdriver (optional) Tin snips (for cutting damper, if required) Scissors “ “ “ Electric drill with ⁄ ⁄ ⁄ (to cut template, if necessary) drill bits Filler blocks or scrap wood pieces, if needed...
  • Page 6 Installation Instructions PLACEMENT OF THE MOUNTING PLATE 4 Cut the middle of the outer protective plastic bag to REMOVING THE MICROWAVE remove the ounting late OVEN FROM THE CARTON/ Screws Screws REMOVING THE MOUNTING Mounting Plate PLATE Remove the installation instructions,use and care, exhaust adapter, turntable ring, shelf, filters, glass bag.
  • Page 7 Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position -beneath framed Plate position -beneath flat bottom cabinet recessed cabinet bottom : I T T A L I R E O C E 8 " T h i s u n t i n l l T p l a t e s e...
  • Page 8 Installation Instructions ALIGNING THE WALL PLATE 3/8" T O EDGE 12" N OTE: IT IS VERY IM PORTAN T TO T rim th e re a r wa ll te m p la te a l o n g th e d o tte d lin e . READ AN D F OLLOW TH E DI RECTION S IN TH E IN STALLATION IN STRU CTION S BEF ORE PROCEEDI N G WITH TH IS...
  • Page 9 Installation Instructions INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to NOTE: NOTE: NOTE: NOTE: NOTE: This microwave is shipped assembled for the following three types of ventilation: Recirculating. Select the type of ventilation required for your installation and proceed to that section.
  • Page 10 Installation Instructions INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING Maximum duct length: NOTE: If you need to install ducts, note that the total duct length of 3 ⁄ ” x 10” (8.2 x 25.4 cm) rectangular or For satisfactory air movement, the total duct length of 5”...
  • Page 11 Installation Instructions EXTERNAL EXHAUST DUCTING OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH USED LENGTH Roof Cap 24 Ft. (7.3 m) 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct 12 Ft. (3.6 m) 12 Ft.
  • Page 12 Installation Instructions OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet Adapting Microwave Blower for Outside Top Exhaust A4. Check Damper Operation Mount Microwave Oven Adjust Exhaust Adaptor 3/ 8" TO EDG he dotted lin wa l l t em plat e a long Trim the rea r...
  • Page 13 Installation Instructions USE TOP CABINET TEMPLATE Carefully pull out the blower unit. The wires FOR PREPARATION OF TOP will extend far enough to allow you to adjust the blower unit. CABINET End B You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor.
  • Page 14 Installation Instructions MOUNT THE MICROWAVE ADAPTING MICROWAVE OVEN BLOWER FOR OUTSIDE TOP EXHAUST Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is tight. Replace blower plate with the screw removed in Step 1. Make sure the screw is tight. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
  • Page 15 Installation Instructions MOUNT THE MICROWAVE ADJUST THE EXHAUST OVEN (cont.) ADAPTOR Open the top cabinet and adjust the exhaust adaptor Cabinet Front to connect to the house duct. Cabinet Bottom Shelf Filler Block Back of Damper Blower Plate Microwave Equivalent to Depth of Cabinet Recess...
  • Page 16 Installation Instructions OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Remove Blower Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet 3 / 8 " TO EDG t h e dotted lin he rea r wa l l t empla t e a long Trim t 12"...
  • Page 17 Installation Instructions ATTACH THE MOUNTING PLATE TO THE WALL • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the Attach the plate to the wall using toggle bolts. TOP CABINET TEMPLATE.
  • Page 18 Installation Instructions ADAPTING MICROWAVE Place the blower unit back into the opening. BLOWER FOR OUTSIDE AFTER: Fan Blade Openings Facing Back BACK EXHAUST (cont.) End A Rotate blower unit counterclockwise 180°. Before Rotation After Rotation End B CAUTION: Do not pull or stretch the blower unit wiring.
  • Page 19 Installation Instructions Cabinet Front MOUNT THE MICROWAVE Cabinet Bottom Shelf OVEN Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL Microwave Oven Top SAFETY, WE RECOMMEND THAT TWO PEOPLE Attach the microwave oven to the top cabinet. INSTALL THIS MICROWAVE OVEN.
  • Page 20 Installation Instructions RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Blower Plate 3 / 8 " TO E D G l i n e. th e rea r w ll tem p l ate a l o n g t h e d o tted T ri...
  • Page 21 Installation Instructions USE TOP CABINET TEMPLATE MOUNT THE MICROWAVE OVEN FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN.
  • Page 22 Installation Instructions MOUNT THE MICROWAVE Open the microwave door and remove the two OVEN (cont.) vent mounting screws ; l ocated on top of the microwave using a #1 Phillips screwdriver. Insert 2 self-aligning screws Charcoal through outer top cabinet Filter holes.
  • Page 23 Installation Instructions For models with the recirculation filter access door Press the bottom of charcoal filter to place it follow these steps to replace or install a PureAir ® into the correct position. Microwave ilter. Remove the PureAir Filter from the packaging ®...
  • Page 24 Installation Instructions Place the new PureAir Filter into the slot ® behind the door at an angle until it's upright and securely placed in the duct. Make sure the PureAir ® Filter is nested vertically in the slot. Close access door,tighten screw and the PureAir Filter is ready to use.
  • Page 25 Installation Instructions BEFORE YOU USE YOUR MICROWAVE Make sure the microwave oven has been Replace house fuse or turn breaker back on. installed according to instructions. CARE Read the Manual. & Remove all packing material from the microwave oven. Install turntable ring a nd glas s tray in cavity.
  • Page 26 3 / 8 " T O E D G E 1 2 " T r i m t h e r e a r w a l l t e m p l a t e a l o n g t h e d o t t e d l i n e . N O T E : I T I S V E R Y I M P O R T A N T T O R E A D A N D F O L L O W T H E D I R E C T I O N S I N T H E I N S T A L L A T I O N I N S T R U C T I O N S...
  • Page 27 Instructions Four à micro-ondes à hotte intégrée d’installation Des questions? Appelez au 1-800-944-9044(US) 1-800-265-8352(Canada) AVANT DE COMMENCER Remarque destinée au consommateur – Lisez attentivement toutes ces instructions. • IMPORTANT – Conservez ces instructions pour vous y reporter • Conservez ces instructions ultérieurement.
  • Page 28 Instructions d’installation INDEX: Adaptation du ventilateur du four à micro-ondes pour l’évacuation à l’extérieur par l’arrière ......17-18 Renseignements généraux Installation du four à micro-ondes ........19 Mesures de sécurité importantes ..........3 Exigences électriques ..............3 Dommages - Expédition/installation ..........4 Recyclage d’air ..............20-22 Pièces comprises ................4 Fixation de la plaque de montage au mur .......20 Outils nécessaires................5...
  • Page 29 Instructions d’installation MESURES DE SÉCURITÉ IMPORTANTES Ce produit nécessite une prise de courant à trois alvéoles Demandez à un électricien qualifié de vérifier la prise mise à la terre. Avant d’entreprendre l’installation, murale et le circuit électrique pour vous assurer que la prise l’installateur doit vérifier la continuité...
  • Page 30 Instructions d’installation DOMMAGES — PIÈCES COMPRISES (SUITE) EXPÉDITION/ SACHET DE QUINCAILLERIE INSTALLATION PIÈCE QUANTITÉ • Si l’appareil est endommagé durant le Gabarit pour transport, retournez-le au magasin où vous l’avez armoire supérieure acheté pour réparation ou remplacement. • Si l’appareil est endommagé par le client, la réparation ou le remplacement reste à...
  • Page 31 Instructions d’installation OUTILS NÉCESSAIRES Règle ou ruban à mesurer et règle droite Crayon Équerre de menuisier Tournevis Phillips n (facultative) Cisailles de ferblantier (pour couper le registre, Ciseaux (pour couper le si nécessaire) Perceuse électrique avec forets gabarit, si nécessaire) de 3/16, 1/2 et 5/8 po Entretoises d’assemblage ou pièces de bois de récupération, si besoin...
  • Page 32 Instructions d’installation INSTALLATION DE LA PLAQUE DE MONTAGE Coupez le centre du sac en plastique pour retirer la plaque ENLEVER LE FOUR À MICRO-ONDES de montage DU CARTON/ENLEVER LE PLATEAU Plaque de DE MONTAGE montage Enlevez les instructions de l'installation, utilisez et prenez soin, adaptateur d'échappement, anneau de la plaque tournante, rayon, filtres, plateau de verre et le petit sac de matétiel.
  • Page 33 Instructions d’installation ÉTABLISSEMENT DE L’EMPLACEMENT DE LA PLAQUE MURALE SOUS VOTRE ARMOIRE Emplacement de la plaque - sous une armoire Emplacement de la plaque - sous une armoire à fond plat dotée d’un rebord R E A D A N D T E : I T I S V ER...
  • Page 34 Instructions d’installation ALIGNEMENT DE LA PLAQUE MURALE Encoches de la Tracez une ligne verticale ligne centrale sur le mur du Centre Trou B d`armoire supérieure La ligne horizontale Zone E Trou A La ligne horizontale Tracez une ligne horizontale sur le mur de fond de "Gabarit pour mur arrière "...
  • Page 35 Instructions d’installation TYPES D’INSTALLATION (Choisissez A, B ou C) Ce four à micro-ondes est conçu pour s’adapter aux trois types REMARQUE: Ce four à micro-ondes est équipé à l’usine en vue d’évacuation suivants : d’une Recyclage Choisissez le type d’évacuation approprié à votre installation et A.
  • Page 36 Instructions d’installation INSTRUCTIONS POUR L`INSTALLATION EXTERIEURE DE CODUITS D`ECHAPPEMENT. Longueur maximale du conduit: REMARQUE : Si vous devez installer des conduits, notez que la longueur totale du conduit rectangulaire de 3-1/4 po x 10 po (8,2 x Pour une circulation d’air satisfaisante, la longueur totale du conduit 25,4 cm) ou du conduit rond de 5 po (12,7cm)/6 po (15,2 cm) de rectangulaire de 3-1/4 x 10 po (8,2 x 25,4 cm) ou du conduit rond de diamètre ne doit pas être supérieure à...
  • Page 37 Instructions d’installation CANALISATION D'ECHAPPEMENT EXTERNE ÉVACUATION À L’EXTÉRIEUR PAR LE DESSUS (EXEMPLE SEULEMENT) Le tableau suivant décrit un exemple d’installation de conduit. LONGUEUR NOMBRE LONGUEUR PIÈCES DE CONDUIT ÉQUIVALENTE UTILISÉ ÉQUIVALENTE Évent de toiture 24 pi (7,3 m) 24 pi (7,3 m) Conduit droit de 12 pi (3,6 m) 12 pi (3,6 m) 12 pi (3,6 m)
  • Page 38 Instructions d’installation ÉVACUATION À L’EXTÉRIEUR PAR LE DESSUS (Conduit vertical) VUE D’ENSEMBLE DE L’INSTALLATION A1. Fixation de la plaque de montage au mur A2. Préparation de l’armoire supérieure 3/ 8" TO EDG E t e a long t h e dotted lin Trim the rea r wa l l t em pla 12"...
  • Page 39 Instructions d’installation UTILISATION DU GABARIT Enlevez délicatement l’ensemble du ventilateur. Les POUR ARMOIRE SUPÉRIEURE fils seront assez longs pour vous permettre d’adapter le ventilateur. POUR LA PRÉPARATION DE L’ARMOIRE SUPÉRIEURE Extrémité A Vous devez percer des trous pour les vis de soutien supérieures, ainsi qu’un trou suffisamment grand pour y faire passer le cordon d’alimentation et une ouverture assez grande pour l’adaptateur d’évacuation.
  • Page 40 Instructions d’installation ADAPTATION DU VENTILATEUR INSTALLATION DU FOUR DU FOUR À MICRO-ONDES À MICRO-ONDES POUR L’ÉVACUATION À L’EXTÉRIEUR PAR LE DESSUS Fixez l’ensemble de ventilateur au four à micro-ondes en utilisant la vis de l’étape 1. Assurez-vous que la vis est bien serrée.
  • Page 41 Instructions d’installation AJUSTEMENT DE INSTALLATION DU FOUR L’ADAPTATEUR D’ÉVACUATION À MICRO-ONDES (suite) Ouvrez l’armoire supérieure et ajustez l’adaptateur Avant de l’armoire d’évacuation pour le relier au conduit d’évacuation Étagère inférieure de l’armoire du domicile. Entretoise Arrière du four Registre Plaque du ventilateur à...
  • Page 42 Instructions d’installation ÉVACUATION À L’EXTÉRIEUR PAR L’ARRIÈRE (Conduit horizontal) VUE D’ENSEMBLE DE L’INSTALLATION B1. Préparation du mur arrière B2. Enlèvement de l’plaque du ventilateur 3 / 8 " TO EDG B3. Fixation de la plaque de montage au mur em plat e a long t h e dotted lin Trim t he rea r wa l l t 12"...
  • Page 43 Instructions d’installation Vous devez percer des trous pour les vis de soutien FIXATION DE LA PLAQUE supérieures, ainsi qu’un trou suffisamment grand pour y faire passer le cordon d’alimentation. DE MONTAGE AU MUR • Lisez les instructions sur le GABARIT POUR ARMOIRE Fixez la plaque au mur à...
  • Page 44 Instructions d’installation ADAPTATION DU VENTILATEUR Replacez l’ensemble du ventilateur dans l’ouverture. DU FOUR À MICRO-ONDES POUR APRÈS : Ouvertures des pales du ventilateur orientées vers L’ÉVACUATION À L’EXTÉRIEUR l’arrière Extrémité A PAR L’ARRIÈRE (suite) Retournez l’ensemble du ventilateur dans le sens contraire des aiguilles d’une montre, sur 180°.
  • Page 45 Instructions d’installation INSTALLATION DU FOUR Avant de l’armoire Étagère inférieure de l’armoire À MICRO-ONDES Entretoise Équivalent à la profondeur du rebord de l’armoire Vis à auto-alignement POUR VOTRE SÉCURITÉ ET POUR FACILITER Dessus du four à micro-ondes L’INSTALLATION, L’INSTALLATION DE CE FOUR DOIT ÊTRE EFFECTUÉE PAR DEUX PERSONNES.
  • Page 46 Instructions d’installation RECYCLAGE D’AIR (évacuation sans conduit) VUE D’ENSEMBLE DE L’INSTALLATION C1. Fixation de la plaque de montage au mur C2. Préparation de l’armoire supérieure C3. Vérification de l’plaque du ventilateur 3 / 8 " T O E D G o n g t h e d o l i n e.
  • Page 47 Instructions d’installation UTILISATION DU GABARIT INSTALLATION DU FOUR À POUR ARMOIRE SUPÉRIEURE MICRO-ONDES POUR LA PRÉPARATION DE L’ARMOIRE SUPÉRIEURE Vous devez percer des trous pour les vis de soutien supérieures, ainsi qu’un trou suffisamment grand pour y faire passer le cordon d’alimentation. POUR VOTRE SÉCURITÉ...
  • Page 48 Instructions d’installation Ouvrez la porte du mirco-ondes et enlevez les deux vis de INSTALLATION DU FOUR montage du tuyau localisés en haut du micro-ondes utilisant  À MICRO-ONDES (suite) un #1 pilote de vis Phillips. Insérez deux vis à auto-alignement Filtre à...
  • Page 49 Instructions d’installation Pour le modèle avec la porte d'accès au filtre de recirculation, suivez ces étapes pour remplacer ou installer un filtre PureAir Appuyez sur fond filtre à charbon pour le placer dans position correcte. et secouez-le pour retirer tout Déballez le filtre PureAir résidu de charbon.
  • Page 50 Instructions d’installation Dans l’orifice situé au dos de la porte, placez obliquement le nouveau filtre PureAir et rabattez-le jusqu’à ce qu’il soit à la verticale et bien fixé dans son emplacement dédié. Veillez à ce que le filtre PureAir soit bien encastré et à...
  • Page 51 Instructions d’installation AVANT D’UTILISER VOTRE FOUR À MICRO-ONDES Réinstallez le fusible ou réenclenchez le disjoncteur Assurez-vous que le four à micro-ondes a été installé conformément aux instructions. du panneau de distribution principal. Lisez le manuel d’utilisation et d’entretien. Enlevez tout le matériel d’emballage du four à...
  • Page 52 R E M A R Q U E : I L E S T T R È I M P O R T A N T D E L I R E E T D E R E S P E C T E R L E S I N S T R U C T I O N S D ' I N S T A L L A T I O N A V A N T C o u p e z l e g a b a r i t p o u r l e m u r a r r i è...
  • Page 53 ¿Preguntas? Llame al 1-800-944-9044(US) 1-800-265-8352(Canada) Nota para el consumidor: Lea estas instrucciones completamente y con atención. • conserve estas instrucciones para referencia futura. • conserve estas • Nivel de preparation tecnica: la instalacion de este instrucciones para uso futuro del inspector local. electrodomestico requiere conocimientos mecánicos y •...
  • Page 54 Instrucciones de instalación CONTENIDO Ajuste del ventilador del microondas para .......17-18 la extracción superior externa Información general Instalación del horno microondas ......19 Instrucciones importantes sobre seguridad ......3 ............20-22 Recirculación Requisitos eléctricos ..............3 Montaje de la placa de instalación en la pared ...............
  • Page 55 Instrucciones de instalación INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Este product require un tomacorriente de tres clavijas con Se debe solicitor a un eléctricista calificado que inspeccione puesta a tierra. Antes de proceder con la instalación del el tomacorriente de pared y el circuito eléctrico correspondi- electrodoméstico, el instalador debe realizar una verificación ente, a fin de asegurarse de que el tomacorriente esté...
  • Page 56 Instrucciones de instalación DAÑOS-ENVÍO (TRANSP PIEZAS INCLUIDAS (CONT.) -ORTE)/INSTALACIÓN KIT DE FERRETERÍA • Si el producto p56-ha resultado dañado durante su envío PIEZA CANTIDAD (transporte), devuélvalo a la tienda/el almacén donde to Plantilla para adquirió, para que lo reparen o lo cambien por uno nuevo. el gabinete •...
  • Page 57 Instrucciones de instalación HERRAMIENTAS NECESARIAS Regla o cinta métrica con borde recto Lápiz Escuadra de carpintero Destornillador Phillips #1 (opcional) Tijera para hojalata (para recortar el regulador de Tijera (para cortar las Taladro eléctrico con brocas extracción,si fuera necesario) plantillas si fuera necesario) ", "...
  • Page 58 Instrucciones de instalación COLOCACIÓN DE LA PLACA DE INSTALACIÓN 4 Come la bolsa de plástico en el medio para retirar la PROCEDIMIENTO PARA SACAR DE placa de instalación. Tornillos LA CAJA EL MICROONDAS Y LA Tornillos PLACA DE INSTALACIÓN Placa de instalación Retirar las instrucciones de instalación, uso y cuidado, adaptador de escape, anillo giratorio, estante, filtros, bandeja de vidrio y bolsa de accesorios pequeña.
  • Page 59 Instrucciones de instalación ALINEACIÓN DE LA PLACA PARA LA PARED 3/8" T O EDGE 12" N OTE: IT IS VERY IM PORTAN T TO T rim th e re a r wa ll te m p la te a l o n g th e d o tte d lin e .
  • Page 60 Instrucciones de instalación TIPOS DE INSTALACIÓN (A Elección Entre A, B o C) Este horno microondas está diseñado para adaptarse NOTA: este horno microondas se p61-ha fábricado para un sistema de Recirculación. Seleccione el tipo de a los tres tipos siguientes de ventilación: A.
  • Page 61 Instrucciones de instalación INSTRUCCIONES DE INSTALACIÓN DE CONDUCTOS DE ESCAPE EXTERNAS NOTA: en caso de que sea necesario instalar conductos, tenga en cuenta Largo máximo del conducto: que el largo total de los conductos. rectangulares (ancho de 3 " × 10" Para lograr una salida satisfactoria del aire, el largo total del u 8,2 cm ×...
  • Page 62 Instrucciones de instalación CONDUCTOS DE ESCAPE EXTERNAS EXTRACCIÓN SUPERIOR EXTERNA (SÓLO EJEMPLO) La siguiente tabla contiene un ejemplo de uno posible instalación de un sistema de conducto de extracción. LARGO (MEDIDAS No DE UNIDADES- LARGO (MEDIDAS PIEZAS DEL CONDUCTO EQUIVALENTES) UTILIZADAS EQUIVALENTES) 24 pies (7,3 m)
  • Page 63 Instrucciones de instalación EXTRACCIÓN SUPERIOR EXTERNA (conducto vertica) DESCRIPCIÓN GENERAL DE LA INSTALACIÓN A1. Montaje de la placa de instalación en la pared. A2. Preparación del gabinete superior. A3. Ajuste del ventilador del microondas para la extracción superior externa. A4. Verificación del funcionamiento del 3/ 8"...
  • Page 64 Instrucciones de instalación USO DE LA PLANTILLA PARA EL Tire del ventilador con cuidado hacia afuera. Los cables GABINETE SUPERIOR A FIN DE se extenderán lo suficiente para permitir el ajuste del PREPARAR EL ÁREA DE DICHO ventilador. GABINETE Extremo B Es necesario taladrar agujeros para los tornillos de soporte superior, realizar un agujero lo suficientemente grande para que el cable eléctuco pueda pasar a través y recortar también un hueco...
  • Page 65 Instrucciones de instalación INSTALACIÓN DEL HORNO AJUSTE DEL VENTILADOR DEL MICROONDAS MICROONDAS PARA LA EXTRAC- CIÓN SUPERIOR EXTERNA Fije el ventilador al microondas con el tornillo previamente retirado en el paso l. Asegúrese de apretar el tornillo. Vuelva a fijar la placa del ventilador con el tornillo previa- mente retirado en el paso 1.
  • Page 66 Instrucciones de instalación INSTALACIÓN DEL HORNO AJUSTE DEL ADAPTADOR DE MICROONDAS (cont.) EXTRACCIÓN Parte delantera del gabinete Abra el gabinete superior y ajuste el adaptador de Extracción para acoplarlo al conducto de la cocina. Estante inferior del gabinete Bloque de relleno Parte trasera del Placa del ventilador Regulador de extracción microondas...
  • Page 67 Instrucciones de instalación EXTRACCIÓN TRASERA EXTERNA (Conducto Horizontal) DESCRIPCIÓN GENERAL DE LA INSTALACIÓN B1. Preparación de la pared trasera B2. Desinstalación del placa del ventilador B3. Montaje de la placa de instalación en la pared B4. Preparación del gabinete superior 3 / 8 "...
  • Page 68 Instrucciones de instalación MONTAJE DE INSTALACIÓN LA PLACA DE EN LA PARED • Lea las instrucciones de la sección PLANTILLA PARA EL GABINETE SUPERIOR. • Adhiera con cinta la plantilla al gabinete superior. Fije la placa en la pared con los tornillos de fiador. •...
  • Page 69 Instrucciones de instalación AJUSTE DEL VENTILADOR DEL Vuelva a colocar el ventilador dentro de su abertura. MICROONDAS PARA LA EXTRAC- DESPUÉS: Aberturas de las aletas del ventilador orientadas CIÓN TRASERA EXTERNA (cont.) hacia atrás. Extremo A Gire el ventilador hacia la izquierda 180°. Antes del giro Después del giro Extremo B...
  • Page 70 Instrucciones de instalación Parte delantera del gabinete INSTALACIÓN DEL HORNO Estante inferior del gabinete MICROONDAS Bloque de relleno Equivalente a la profundidad de la superficie hueca del gabinete Tornillo autoalineante POR RAZONES DE SEGURIDAD PERSONAL Y PARA FACILITAR LA Parte superior del horno microondas INSTALACIÓN, SE RECOMIENDA QUE DOS PERSONAS INSTALEN EL HORNO MICROONDAS.
  • Page 71 Instrucciones de instalación RECIRCULACIÓN (Sin Conducto De Extracción) DESCRIPCIÓN GENERAL DE LA INSTALACIÓN C1. Montaje de la placa de instalación en la pared C2. Preparación del gabinete superior C3. Verificación del conjunto del Placa del Ventilador 3 / 8 " T O E D G w a l l p l ate a l o...
  • Page 72 Instrucciones de instalación INSTALACIÓN DEL HORNO USO DE LA PLANTILLA PARA EL MICROONDAS GABINETE SUPERIOR A FIN DE PREPARAR EL ÁREA DE DICHO GABINETE Es necesario taladrar agujeros para los tornillos de soporte superior, así como un agujero lo suficientemente grande para que el cable eléctrico pueda pasar a través.
  • Page 73 Instrucciones de instalación INSTALACIÓN DEL HORNO Abra la puerta del microondas y saque los dos tornillos MICROONDAS (cont.) de montaje de ventilación ubicados en la parte superior del horno con un destornillador Phillips #1. Inserte 2 tornillos autoalineantes a través de los agujeros exteriores del gabinete superior.
  • Page 74 Instrucciones de instalación Para el modelo con la puerta de acceso al filtro de recirculación, siga Presione la parte inferior del filtro de carbón para colocarlo las instrucciones para remplazar o instalar un filtro PureAir ® en la posición correcta. Quitar el filtro PureAir del empaque y sacudir para quitar el exceso de carbón.
  • Page 75 Instrucciones de instalación Coloque el nuevo filtro PureAir en la ranura detrás ® de la puerta en un ángulo hasta que esté en posición vertical y firmemente colocado en su sitio. Asegúrese de que el filtro PureAir esté instalado ® verticalmente en la ranura.
  • Page 76 Instrucciones de instalación ANTES DE USAR EL HORNO MICROONDAS Vuelva a colocar el fusible correspondiente o encienda de Asegúrese de que el horno microondas haya sido instalado nuevo el disyuntor. según las instrucciones. Lea el manual de use y cuidado. Retire todo el material de empaque del horno microondas.
  • Page 77 3/8" HASTA EL EXTREMO 12" NOTA: ES MUY IMPORTANTE LEER Y SEGUIR LAS Corte la plantilla ubicada en la pared de atrás a través de la linea de puntos. DIRECCIONES EN LAS INSTRUCCIONES DE INSTALACIÓN ANTES DE PROCEDER CON ESTA PLANTILLA DE PARED POSTERIOR.