Installing And Replacing Batteries - NAD C 542 Manuel D'installation

7. To terminate program play, press STOP. However the stored
track list remains in memory; if you want to play the program
again, simply press PLAY again. If you want to edit the program,
press PROGRAM repeatedly to review the list and change. To
add tracks, press the PROGRAM button until the highest
program number is displayed.
8. To clear the program memory, press STOP twice, OPEN/CLOSE
to open the drawer, or switch off the POWER.
The following example presents a step-by-step illustration of how to
program and start Program Play to play tracks 5, 23, 9, 16, and 1.
While the CD player is stopped:
Press on remote control Display shows
PROGRAM
5
PROGRAM
+10, +10, 3
PROGRAM
9
PROGRAM
+10, 6
PROGRAM
1
PROGRAM
PLAY
The Calendar display track listing will indicate the selected
program.
DELETE
The C 542 CD Player allows to user to delete unwanted tracks in
any desired order in either the Program Mode or the Stop Mode.
To Delete tracks, use the sequence of commands below.
In Program Mode:
1. Press DELETE. The display indicates "dE d:01"; the player is
now ready for first Delete entry. "dE" will change to first
memory track after 1 second.
2. Use the SKIP & SKIP
track you would like to delete. The track number will flash.
3. Press DELETE again to store the selected track number in
memory. The selected track number will be deleted in the
display. The display will advance to next location. This
showing that the player is ready for your second entry.
4. Repeat Steps 2 and 3 to select the delete the track numbers
in memory, up to a maximum of 20 entries but cannot delete
track above track 25.
5. To play the stored program, just press PLAY. During playing,
the SKIP buttons will access only the tracks still listed. The
deleted songs are not listed.
6. To clear the memory, press STOP twice, OPEN/CLOSE to
open the drawer, or switch off the power.
In Stop Mode:
1. Press DELETE. The display indicates "dE d:01" with total
track time. The player is ready for the first Delete entry.
2. Use the Direct-Entry Numeric keypad buttons to select the
first track you would like to delete. The selected track
number will be deleted in the calendar display and the
updated total playing time is shown on display.
Repeat Steps 2 to select the track numbers you would like to
3.
delete, up to a maximum of 25 entries but cannot delete
track above track 25.
4. To play the remaining tracks, just press PLAY. During playing,
the SKIP buttons will access only the tracks still listed. The
deleted songs are not listed.
5. To clear the memory, press STOP, OPEN/CLOSE to open the
The Calendar display will indicate remaining track listing. After
completing playback, the C 542 will automatically stop, and the
display will again show all the tracks contained on the inserted
CD.
NOTE: In the Program-entry mode, the SKIP
buttons have a "wrap-around" function: if you SKIP Back
repeatedly from Track 01, the number counts down from the final
track on the disc. This provides a convenient way to select high-
numbered tracks.
Pr p:01

INSTALLING AND REPLACING BATTERIES

5 p:01
The remote control requires two 1.5-volt AAA-size (i.e. UM-4 or
Pr p:02
IEC RO3) cells. Alkaline cells are recommended, to obtain
23 p:02
maximum operating life. To open the battery compartment, place
Pr p:03
your fingertip in the recess on the rear of the remote control, push
9 p:03
against the flexible edge of the battery cover and lift the cover
Pr p:04
upwards. Install fresh cells, orienting them as shown on the
16 p:04
diagram within the compartment.
Pr p:05
1 p:05
The coil springs should contact the (-) end of each cell. Push the
Pr p:06
battery compartment cover back and press gently until it latches.
In some cases, corrosion or fingerprint oil on the battery contacts
may cause poor operation. Remove both cells, rub the metal
contacts at both ends of each cell with a clean cloth or a pencil
eraser, and re-install the cells, being careful to orient them
correctly.
Developed by Pacific Microsonics in the USA, HDCD
Definition Compatible Digital
process for delivering the full richness and detail of the recording.
HDCD
20-bits of real musical information, as compared to 16-bits for all
buttons to select the first
other CDs. HDCD
format by using a sophisticated system to encode the additional
four bits onto the CD while remaining completely compatible with
the existing CD format.
The result is a larger dynamic range, a more focused 3-D
soundstage, and natural vocal and musical timbre. An HDCD-
encoded disc played on the HDCD-equipped NAD C 542 CD player
produces audibly superior clarity and depth. Enhanced
performance will also be obtained from standard CDs.
The NAD C 542 CD player will automatically identify an HDCD
encoded disc and activate its HDCD
will light up when it's playing an HDCD
CD-R & VD-RW AUDIO DISCS
The C 542 can play back CD-R, CDRW audio discs that have been
recorded on a computer or CD-recorder. The quality of CD-R,
CD-RW audio discs varies widely which may affect playability.
Some factors that affect playability:
• The quality of the disc itself. Generally speaking, CD-R, CD-RW
• The quality of CD-recorder or computer CD re/writer. Some
• The CD-R & CD-RW was created with high-speed writing. In
drawer, or switch off the power.
) is a patented encode/decode
®
® encoded CDs sound better because they are encoded with
overcomes the limitation of the 16-bit CD
®
blanks from well-renowned companies give better results
than unbranded ones.
recorders and writers produce better results than others.
and
® (High
®
® decoder. The red indicator
encoded disc.
®