Cleaning And Maintenance - MediaShop Livington PRIME Ultimate Mode D'emploi

3. Tube Connection:
Insert the aluminum tube into the appliance (Illu. 8), holding the two pins corresponding to the two holes on
the appliance, then firmly secure the aluminum tube.
4. Brush Connection:
press the ON/OFF BUTTON to switch on the vacuum cleaner, then the appliance starts to suck, the four blue
LEDs light up; after 7 to 8 minutes, the first blue light goes out, after 13 to 14 minutes the second and after
17 to 18 minutes the third and fourth. Clean the filter after each use. Then restart the sucker so that it runs
properly again.
5. LED-Display:
Move the vacuum cleaner to a trash can, then pull out the dust collector on the handle (Illu. 11) and empty the
dust, clean the bowl, and immediately replace it; Clicking sounds indicate that the shell is snapped in again
(Illu. 12-13). Turn clockwise to remove and clean the HEPA filter, then reinsert clockwise.
6. Cleaning of the Dust Collection Container, including HEPA-Filter:
1. Pull the dust container out of its holder: Hold the white tab in the middle in place with two fingers and pull
the container out (Illu. 21).
2. Open the dust container over a dustbin, by unlocking the flap underneath the dust container, in order to
empty the dust out (Illu. 22).
3. To clean the filter turn it in an anti-clockwise direction and brush it off, then reattach it to the dust
container by turning it in a clockwise direction.
4. After cleaning, reinsert the dust container by sliding it directly into the appliance with a firm push.
7. 3-in-1 Combination Brush:
This appliance is equipped with a 3-in1-combination brush, consisting of a grout nozzle for narrow gaps (a),
brush attachments (b) and the furniture brush (c) – see (Illu. 14). press the locking mechanism to remove
the brushes head; the nozzle can be used for cleaning narrow gaps; brush attachments can be used for the
cleaning of, for example, computer keyboards and the rear-side can be used as a furniture brush.
8. Flexible tubing:
In order to to release the flexible tubing (See illustration page 4), press briefly on the release knob and gently
bend the tube forwards. The lock is then detached. Following use, let the lock click back into place.
PRECAUTIONARY MEASURES
1. When the battery is inserted in the charging station, the red light flickers and shows the charging process,
ending with the green light, which means „fully-charged".
2. If the appliance is not in use for a long period of time, the charge level of the battery will decrease; please
recharge the battery, once or twice, every six months.

CLEANING AND MAINTENANCE

I. Cleaning the Appliance:
1. All routine maintenance and repair tasks should be carried out following display of a charged appliance.
2. Following every period of use the dust collection container should be cleaned.
3. When not in use, the appliance should be kept in a cool and dry place, and not be exposed to direct
sunlight or dampness.
4. Ensure that the appliance is kept separate from the power supply and the ON/OFF buttons switched off;
wipe it down with a damp, cotton towel (with water or a neutral cleaner), without letting water or cleaner
get inside and causing defects.
II. Brush Cleaning:
Insert a coin into the roller lock as shown in Illu. 15, turn clockwise and unlock, open the roller cover plate (Illu.
16), remove the brush roller and remove hair and dirt from the roller. Long hair can also be cut up with scissors
before removal. Then replace the brush and close the roller lock with coin.
STORAGE OF THE APPLIANCE
When not in use, hang the device in the charging station (Illu. 6). • Hang the flat suction brush against the left
hook of the device, slide the suction tube onto the right hook and plug in the brush.
14
M17133_Livington_PrimeULTIMATE_Manual_20180709__DR.indd 14 09.07.18 12:42