Cequent Performance Products 51235 Instructions D'installation
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
rail
Hitch
Shown In Proper
Equipment Required:
Fastener
Kit:
51235F
Wrenches:
3/4, 21mm & 22mm
Drill
Bits:
None
Frame
Existing weldnut
Note: Fasteners typical both sides
O
Qty. (2)
Hex
bolt
M14
Qty. (2)
Lock
washer
Qty. (2)
Flat washer
O
Qty. (6)
Carriage bolt 1/2-13X 1-3/4" GR5
Fasteners Tvpical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
Note: Loosen the spare tire for ease of installment
Remove existing M14 bolts from end of each frame rail.
1.
Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
2.
3.
Install new M14 bolts through receiver into weldnuts in vehicle frame and into step bumper.
Install remaining fasteners as shown.
4.
5. Tighten all fasteners to the required torque specification.
6. Re-tighten the spare tire
Tighten all M14 CLIO.9 fasteners with torque wrench to 100 Lb.-Ft. (136 N*M)
Note: check hitch
ently,making sure all fasteners andballareprolprlytightened. I f hitchis removed, plugall holes in ü-unk panor other bodypanels to prevent
entryof waterandex austfumes. A hitch or ball which hasbeendamaged shouldberemovedandreplaced.Observe safetyprecautions w henworkingbeneath a
vehicle and wear eye protection. Do not cut accessor attachmentholes with a torch.
This productcomplieswith safetyspecifications andrequirements f or connecting devicesandtowing systems of thestateof New York, V.E.S.C.RegulationV-5 and
SAE
J684.
02013
Cequent
Performance
Products,
Printed in Mexico
Installation
Chevrolet Silverado Pickup 1500
GMC Sierra Pickup 1500
(Requires OEM Bumper)
Note : Factory installed
steel step bumper and
brackets
must
conjunction with this
Position
hitch
rail
O
X 2.0
X 40mm
CL
10.9
9/16"
9/1 6"
Tighten all 1/2-13GR5 fasteners with torque wrench t075 Lb.-Ft. (102 N*M)
lnc
Instructions
Do Not Exceed Lower of Towing Vehicle
Hitch type
be used in
Weight Distributing
Weight Carrying
Ball
Mount
Wiring Access Location:
4
6
O
Qty. (6)
Qty. (6)
Ø
Qty. (6)
Sheet
1 of
3
Manufacturer's
Rating or
Max
Gross
Trailer wr
(LB)
8000 (3632 Kg)
5000 (2270 Kg)
PU3
Accessory Rating
Cross member and step
bumper shown in cut
view for clarity
Note : Factory installed
steel step bumper and
brackets
must be used in
conjunction with this
hitch
Spacer
Conical
washer
h"
Hex
nut
1413
51235N
9-20-13
Form: F205
Part Numbers:
51235
Max Tongue
800 (363 Kg)
500 (227 Kg)
c
Rev.
B
C 9-17-2012
Manuels Connexes pour Cequent Performance Products 51235
Sommaire des Matières pour Cequent Performance Products 51235
- Page 1 Frame rail Part Numbers: Installation Instructions 51235 Chevrolet Silverado Pickup 1500 GMC Sierra Pickup 1500 (Requires OEM Bumper) Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or Note : Factory installed Gross Max Tongue Hitch type steel step bumper and...
- Page 2 Observer les mesuresde sécuritéappropriéesen travaillant sous le véhiculeet porter des lunettes de protection. Ne jamais utiliser une torche pour découperun accesou un trou de fixation. Ce produitest contorme aux normes V-5 et SAE J684 de Ia V.E.S.C. (Etat de New York) concernant les spécificationsen matiére de sécurité des systemesd' attelage. 0 2013 Cequent Performance Products, Inc Feuille 2 de 3 51235N Rev.
- Page 3 Observelas precaucionesde seguridadal trabajarpor debajo del vehiculo y use protecci6n visual. No corte los orificios de accesoo accesorioscon soplete. te produ cume%cy especificaci ones ytequisito de seguridad para conectar dispositivos ysistemas de remolque del estado de Nueva York, V.ES.C. Regulaciön V-5 y 02013 Cequent Performance Products, Inc. Hoja 3 de 3 51235N Rev. B In-preso en M...