Extreme Max 3005.7240 Instructions D'utilisation Et D'entretien
Les langues disponibles
Les langues disponibles
Liens rapides
-naäuC7$
Pontoon
skirting
may need to be removed
Mount TM . Re-install
skirting
Tools required:
2 C-Clamps
(3" recommended)
6 mm
Allen
Wrench
1/4"
Drill
Bit
13/32"
Drill
Bit
10mm
Wrench
or Socket
15mm
Wrench
or Socket
Drill
Marker
Product
Satisfaction
At Extreme Max, we pride ourselves
not 100% satisfied with the product, for any reason, please reach out to us. We are here to help!
Warranty
This product is warranted
for consumer
Warranty
valid
only in the USA.
This product is warranted
to the original
wear and tear expected.
This warranty
of goods or any acts of vandalism
commercial
use. The sole remedy under this warranty
or similar
product, or the refund of the original
or incidental
damages. Any and all freight charges to handle warranty
Extreme MaxTM is not responsible
For all inquries please send your name, mailing
summary
of alleged defect and any applicable
Customer Service: service@extrememax.com
Pontoon
Installation
to install Pontoon
after installation
is complete.
Hardware
Included:
(6)
- 10mm
x 25mm
(2)
- 10mm Nylon Flange Nuts
(4)
- 10mm
Clinch
(1)
- 10mm
x 20mm
(1)
- 10mm
Zinc-Plated
(6)
- M6 x 25mm Carriage Bolts
(6)
- M6 Nylon Flange Nuts
(6)
- M6 Flat Washers
Guarantee
on making quality
use for 2 years after the date of retail purchase. Warranty
retail purchaser to be free from defects in material
shall not apply to any defects caused by: (l) overloading,
by any person, (Ill) improper
is at the discretion
purchase price. Extreme MaxTM is not responsible
for any labor charges that may be incurred.
address, main contact phone number,
pictures to service@extrememax.com.
Accessory
Instructions
Accessory
Button
Head
Bolts
Nuts
Zinc-Plated
Hex
Head
Washer
products
and wish to correct any mistakes on our end. If you are
installation
or use contrary to the instructions,
of manufacturer:
claims are the responsibility
I www.extrememax.com
MountTM
3005.7240
Bolt
includes
parts only.
and workmanship,
ordinary
(II) physical abuse
(IV)
the replacement
of the same
for any consequential
of the consumer.
original
retail sales receipt,
ProjectNo. Here
Manuels Connexes pour Extreme Max 3005.7240
Sommaire des Matières pour Extreme Max 3005.7240
- Page 1 - M6 Flat Washers Product Satisfaction Guarantee At Extreme Max, we pride ourselves on making quality products and wish to correct any mistakes on our end. If you are not 100% satisfied with the product, for any reason, please reach out to us. We are here to help!
- Page 2 Slide Rails Mount Plate Mount Plate Bracket Side A Side AN Inside Inside Side B C-Clamp Side C-Clamp Step 1: Loosen mount plate bolts to adjust slide arm width. Align slide arms of Pontoon Accessory MountTM to be flush with the inside pontoon rails.
- Page 3 * Tip: Tape the outside of the pontoon rails to prevent scratching. Step 5 step 6: Remove slide arms from pontoon rails. Important: Do not drill through slide arm holes. Use 1/4" drill bit to drill a pilot hole in locations marked in step 5.
- Page 4 Marqueur - M6 Rondelles Plates Garantie De Satisfaction Du Produit Chez Extreme Max, nous sommes fiers de fabriquer des produits de qualité et souhaitons corriger toute erreur de notre part. Si vous n'étes pas satisfait å 100% du produit, pour quelque raison que ce soit, veuillez nous contacter.
- Page 5 Glissiéres Support De Plaque Plaque De Montage De Montage Side A Side AX Inside Inside Side B C-Clamp Side C-Clamp Étape 1: Desserrer les boulons de la plaque de montage pour ajuster la largeur du bras coulissant. Alignez les bras coulissants du support d'accessoire...
- Page 6 * Conseil: Scotchez I'extérieur rails ponton pour éviter Ies rayures. Step 5 Etape 4: Étape 6: Positionnez les bras coulissants le long de l'extérieur Retirez les bras coulissants des rails du ponton. des rails du ponton. Placez un boulon de 10 mm Important: Ne percez pas dans les trous des bras dans le trou foré...