Télécharger Imprimer la page

Liens rapides

ONE
THARNESS INSTALLATION
THAR-ONE-TOY1
INSTALLATION HARNAIS
VEHICLE
VEHICULES
TOYOTA
Yaris
(40-Bit)
HARDWARE VERSION
VERSION MATÉRIELLE
MINIMUM
MANDATORY INSTALL | INSTALLATION OBLIGATOIRE
HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED)
* HOOD PIN
MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE
STARTED WITH THE HOOD OPEN.
CONTACT
STATUT DE CAPOT : LE CONTACT DE CAPOT (INCLUS), DOIT
DE CAPOT
ÊTRE INSTALLÉ SI LE VÉHICULE PEUT DÉMARRER À DISTANCE,
LORSQUE LE CAPOT EST OUVERT.
1 / 7
Page
Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule
YEARS
ANNÉES
2006-2010
7
Program bypass option:
Programmez l'option du contournement:
REV.: 20190109
supportées dans ce diagramme (fonctionnelles si équipé)
BYPASS
FIRMWARE VERSION
FLASH LINK UPDATER or FLASH LINK MOBILE tool,
[
]
79.
48
TOYOTA/LEXUS/
MINIMUM
SUBARU
UNIT OPTION
OPTION UNITE
C1
Notice: the installation of safety
elements are mandatory. The hood pin
SECURITY STICKER
and the sticker are essential security
elements and must be installed.
AUTOCOLLANT DE
Notice: l'installation des éléments de
SÉCURITÉ
sécurité est obligatoire. Le contact de
WARNING
capot et l'autocollant de sécurité sont
ATTENTION
des éléments de sécurité essentiels et
Included
doivent absolument être installés.
Inclus
Guide # 82951
ADDENDUM - SUGGESTED WIRING CONFIGURATION
ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ
To add the firmware version and the options, use the
sold separately.
Pour ajouter la version logicielle et les options,
utilisez l'outil FLASH LINK UPDATER
ou FLASH LINK MOBILE, vendu séparément.
DESCRIPTION
OEM Remote status (Lock/Unlock)
monitoring
Suivi des status (Verrouillage/Déverrouil-
lage) de la télécommande d'origine
THIS MODULE MUST BE INSTALLED BY A
QUALIFIED TECHNICIAN. A WRONG
CONNECTION CAN CAUSE PERMANENT
DAMAGE TO THE VEHICLE.
CE MODULE DOIT ÊTRE INSTALLÉ PAR
UN TECHNICIEN QUALIFIÉ, TOUTE
ERREUR DANS LES BRANCHEMENTS
PEUT OCCASIONNER DES DOMMAGES
PERMANENTS AU VÉHICULE.
loading

Sommaire des Matières pour Fortin 82951

  • Page 1 1 / 7 Guide # 82951 REV.: 20190109 Page THARNESS INSTALLATION ADDENDUM - SUGGESTED WIRING CONFIGURATION THAR-ONE-TOY1 INSTALLATION HARNAIS ADDENDA - SCHÉMA DE BRANCHEMENT SUGGÉRÉ Vehicle functions supported in this diagram (functional if equipped) | Fonctions du véhicule supportées dans ce diagramme (fonctionnelles si équipé)
  • Page 2 This guide may change without notice. See www.fortin.ca for latest version. 2 / 7 Page Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version. DESCRIPTION | DESCRIPTION At Parking light switch harness At Steering Column...
  • Page 3 This guide may change without notice. See www.fortin.ca for latest version. 3 / 7 Page Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version. AUTOMATIC TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION AUTOMATIQUE Yellow...
  • Page 4 This guide may change without notice. See www.fortin.ca for latest version. 4 / 7 Page Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version. MANUAL TRANSMISSION WIRING CONNECTION | SCHÉMA DE BRANCHEMENT TRANSMISSION MANUELLE Yellow...
  • Page 5 This Guide may change without notice. www.ifar.ca for latest version. 5 / 7 Page Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version. Ce Guide peut faire l'objet de changement sans préavis. www.ifar.ca pour la récente version. KIA RIO - PUSH-TO-START KEY BYPASS PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION CONTOURNEMENT DE CLÉ...
  • Page 6 6 / 7 Page Ce guide peut faire l’objet de changement sans préavis. Voir www.fortin.ca pour la récente version. REMOTE STARTER PROGRAMMING PROCEDURE | PROCÉDURE DE PROGRAMMATION DU DÉMARREUR À DISTANCE REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.
  • Page 7 The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way.