SIGNIFY Sunstay Pro gen2 VGP726 Hybrid Manuel D'installation
Sunstay Pro gen2
VGP726 Hybrid
The luminaire should be positioned so that prolonged staring into
the luminaire at a distance closer than 0,384 m is not expected
Connect the battery for luminaire operation
This luminaire must be installed by qualified personnel only
Disconnect battery and panel before servicing
Use gloves to install/service the luminaire
Always follow this mounting instructions to fix the luminaire
Never modify the luminaire nor the fixation locations for installation
Risk of accident due to incorrect tightening torque
583 - 443000022505
QR
2025-08-26
15 x 15
© Signify Holding
All rights reserved
07
IK
66
09
IK
IP
PV panel
1/11
outdoor
Data subject to change without notice
Keep for future reference:
4-10
www.signify.com
Manuels Connexes pour SIGNIFY Sunstay Pro gen2 VGP726 Hybrid
Sommaire des Matières pour SIGNIFY Sunstay Pro gen2 VGP726 Hybrid
- Page 1 Never modify the luminaire nor the fixation locations for installation Risk of accident due to incorrect tightening torque 583 - 443000022505 2025-08-26 15 x 15 1/11 Data subject to change without notice © Signify Holding Keep for future reference: www.signify.com All rights reserved...
- Page 2 Dimensions S.Cx values Energy efficiency class 2/11...
- Page 3 For optimal performance of the luminaire contact your local SIGNIFY employee for solar sizing and configuration. The installation of the luminaire is not recommended under these conditions: The luminaire performance and battery charging can be affected by external parameters. Additional photovoltaic vertical panels can be fixed to the pole.
- Page 4 Spigot fixation Luminaire orientation Post Top (PT): Side Entry (SE): Ø76mm or Ø60mm Only Ø60mm Open luminaire only if base is supported or Spigot into pole if luminaire is installed on the pole 4/11...
- Page 5 Mains connection 5/11...
- Page 6 Sensors and type of luminaire Optional : Top sensor: Philips Outdoor Light Control (OLC) Optional : Bottom sensor: Philips Outdoor Multi Sensor (OMS) 6/11...
- Page 7 Disconnect Battery and PV panel first before disconnecting or upgrading the product from A or B to C or D Luminaire A or B: Charge Controller CC G5 is connected to BLE Bluetooth module Luminaire C or D: Charge Controller CC G5 is connected to DFLEX Contact your local SIGNIFY employee for further information Recomended luminaire cleaning 7/11...
- Page 8 Watch out to the installation date. The battery is 70% level charged when leaving factory. Depending on storage time and ambient temperature, the battery can lose some charge. The labels in the luminaire containe a QR code. For any contact with SIGNIFY regarding the product, please scan the QR code an keep it for reference.
- Page 9 Opbevaring, installation, brug, betjening og vedligeholdelse af produkterne må kun udføres ifølge instruktionerne i denne vejledning og/eller eventuelle øvrige instruktioner fra Signify for at garantere sikker brug af produktet i hele dets levetid. Hvis disse instruktioner ikke følges, bortfalder produktgarantien. Bolte/skruer med angivet spændingsmoment på...
- Page 10 Η αποθήκευση, η εγκατάσταση, η χρήση, η λειτουργία και η συντήρηση των προϊόντων πρέπει να γίνεται ακριβώς σύμφωνα με τις οδηγίες του παρόντος εγχειριδίου ή / και τις άλλες οδηγίες που ενδεχομένως να παρασχεθούν, προκειμένου να είναι εγγυημένη η ασφαλής χρήση του προϊόντος...
- Page 11 The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify. All trademarks are owned by Signify Holding or their respective owners.