1. Manuels
  2. Marques
  3. Costway Manuels
  4. Ameublement d'intérieur
  5. HV10800
  6. Mode d'emploi

Costway HV10800 Mode D'emploi

Masquer les pouces

Table des Matières

Coffee Table
Table Basse
HV10800
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Table des Matières
loading

Manuels Connexes pour Costway HV10800

Sommaire des Matières pour Costway HV10800

  • Page 1 Coffee Table Table Basse HV10800 THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

  • Page 2: Before You Start

    Before You Start Please read all instructions carefully. Retain instructions for future reference. Separate and count all parts and hardware. Read through each step carefully and follow the proper order. We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.

  • Page 3: Avertissement D'assemblage

    Assembly Warning ● Assembling with 2 or more people is recommended. ● Please assemble at a spacious and flat place ● Please place blankets or cardboard so floor or walls will not be scratched ● Please ventilate the area if there is a strong glue odor after opening the product ●...
  • Page 4 Hardware/Accessoires Before assembly, inspect unit for missing parts. Be sure that children do not accidentally swallow these parts. ※Same sized parts are in a bag. Please check the size of the screws. /Avant l'assemblage, vérifiez qu'il ne manque aucune pièce. Veillez à ce que les enfants n'avalent pas accidentellement ces pièces.
  • Page 5 Parts/Pièces...
  • Page 6 Top Panel (Long) Top Panel (Short) Bottom Panel /Panneau /Panneau /Panneau inférieur supérieur (long) supérieur (court) 1 x1 2 x1 3 x1 Side Panel (L) Side Panel (R) Center Panel /Panneau latéral (G) /Panneau latéral (D) /Panneau central 4 x1 5 x1 6 x1 Internal Support Panel...

  • Page 7: Assembly Information/Informations D'assemblage

    Assembly Information/Informations d’Assemblage ● Assemble screws/Assembler les vis 1. Screw up to half 2. Tighten all point to make sure screws all spots are lined up /2. Serrer toutes /1. Visser jusqu'à la les vis. moitié de la pointe pour s'assurer que tous les points sont alignés.
  • Page 8 ● Assemble Cam Bolt/Assembler boulon de came 1. Screw up cam bolt into 2. Insert cam bolt into holes. holes. Tighten all cam bolts. Set the arrow of the screw up toward the nut slot. /1. Visser le boulon de came dans les trous.

  • Page 9: Assembly Step/Étape D'assemblage

    Assembly Step/Étape d’Assemblage Failure to follow these directions could cause poor strength or stability. Insert screws loose to line up with slots then tighten up each screw. /Le non-respect de ces instructions peut entraîner une diminution de la résistance ou de la stabilité. Insérer les vis sans les serrer pour les aligner avec les fentes, puis serrer chaque vis.
  • Page 11 CLOSE /FERMER Installation: As shown, the head of cam lock enters the opening of the cam bolt. Use Allen key to turn the cam lock to tighten the cam bolt. /Installation : Comme indiqué, la tête du verrou de came entre dans l'ouverture du boulon de came.
  • Page 12 CLOSE /FERMER Installation: As shown, the head of cam lock enters the opening of the cam bolt. Use Allen key to turn the cam lock to tighten the cam bolt. /Installation : Comme indiqué, la tête du verrou de came entre dans l'ouverture du boulon de came.
  • Page 13 CLOSE /FERMER Installation: As shown, the head of cam lock enters the opening of the cam bolt. Use Allen key to turn the cam lock to tighten the cam bolt. /Installation : Comme indiqué, la tête du verrou de came entre dans l'ouverture du boulon de came.
  • Page 14 CLOSE /FERMER Installation: As shown, the head of cam lock enters the opening of the cam bolt. Use Allen key to turn the cam lock to tighten the cam bolt. /Installation : Comme indiqué, la tête du verrou de came entre dans l'ouverture du boulon de came.
  • Page 15 Use hammer to tighten foot pads /Utiliser un marteau pour serrer les patins Use screwdriver to tighten screws /Utiliser un tournevis pour serrer les vis...
  • Page 16 COMPLETED/TERMINÉ...

  • Page 17: Instructions De Retour / Réclamation De Dommages

    Return / Damage Claim Instructions DO NOT discard the box / original packaging. In case a return is required, the item must be returned in original box. Without this your return will not be accepted. Take a photo of the box markings. A photo of the markings (text) on the side of the box is required in case a part is needed for replacement.
  • Page 20 FRA office: Saint Vigor d'Ymonville GBR office: FDS Corporation Limited, Unit 4, Blackacre Road, Great Blakenham, Ipswich, IP6 0FL, United Kingdom USA:cs.us@costway.com AUS:cs.au@costway.com If you're having difficulty, our friendly GBR:cs.uk@costway.com customer team is always here to help. FRA:cs.f r @costway.com...

Table des Matières