Konect 100A Manuel D'instructions

INSTRUCTION MANUAL
100A
Sensored Brushless ESC For cars
# KN-ELITE-ESC100
SPECIFICATION
•32 bit processor •Low resistance FET •Continuous current
Forward/Brake/Reverse: ----- Yes (Factory preset at Forward/Brake)
Model: 100A
Dimensions: 44.5x39.5x31mm(including fan)
Weight: 73g(including wires)
Voltage Input:
2S - 2S HV
Continuous current: 100A
Peak Current: 180A
Motor limit >=8.5T
Motor Type: Sensored 380/390/540 brushless motors
6V - 7.4V / 4A
B.E.C:
INSTALLATION & CONNECTORS
+ Positive electrode
Lipo battery
2S
- Negative
electrode
Capacitor
- Black
+Red
C
CH4
+
CH3
B
CH2
Ch1 -
A
A
Receiver
A B C
Bec cable
Power Switch
Sensor cable
1. Connect build in BEC wire(100mm) between the receiver connector and ESC.
2. Directly to the motor or use your favorite connectors. Match the label of the ESC
Output (A, B, C) to the Tablabels on the motor when soldering. Avoid soldering each
joint for longer than 5 seconds. Prior to operation make sure you have not created a
short by either eating a wire bridge or solder bridge on the solder tabs on the motor.
(WARNING! Improper wiring may damage the ESC and void the warranty.)
DECLARATION
This is Electronic Speed Controller (ESC) for car. High power system for RC
model is very dangerous, so please read this manual carefully. Since we
can't control over the correct use, installation, application, or maintenance
of our products, we've no liability shall be assumed nor accepted for any
damages, losses or costs resulting from the use of the product. Any claims
arising from the operating, failure of malfunctioning etc. will be denied.
We assume no liability for personal injury, consequential damages
resulting from our product or our workmanship.
RADIO & ESC SETUP
Transmitter Settings:
• Throttle Travel Maximum / 100%
• Brake Travel Maximum / 100%
• Throttle Exponential Start with 0%
• Throttle Neutral Trim Center / 0
• Throttle Servo Reverse (Futaba, KO, Sanwa)
The initial set-up of the throttle end-points of the ESC:
1. Connect the power wires of the ESC to a fully charged
2. Bind your receiver and transmitter first if your radio requires you to do so.
3. Press and hold the ESC set button and then switch on the ESC, release the button unit
the led change to blue and flash from red, you can listen to two beeps sound from
motor at the same time.
4. Keep the throttle in the neutral position and then press the set button, the neutral
position already memory on ESC when listen to a beep sound.
+
5. Full throttle and then press once the set button, the maximum throttle position
already memory on ESC when listen for two beeps sounds.
6. Full brake and then press once the set button, the maximum brake position already
memory on ESC when listen for three beeps sounds.
7. A beep will then sound, Signifying that the ESC endpoints have been successful.
LED Status in Driving Mode:
1.Normal Running:
Throttle in the neutral position: The green LED lights, red LED off. In Zero Timing, the
C
green LED flashes slowly. (Boost 0°, Turbo 0°) Compliant with ROAR competition rules
Moving forward: The green LED off, the red LED flashes from slowly to quickly as the
B
throttle move forward; The red LED lights when move forward to top point of maximum
throttle.(100% throttle)
Braking/Backward: The green LED off, the red LED flashes from slowly to quickly as the
throttle move backward; The red LED lights when move brake/backward to top point of
maximum brake/backward. (100% brake/backward)
2.Protection Function:
When the ESC does not detect the throttle signal: The orange LED lights.
Abnormal battery voltage: The orange LED flashes once.
When the ESC is in low voltage protection status: The orange LED flashes twice.
When the ESC is in temperature protection status: The orange LED flashes three
times.
When the ESC disconnect with the sensor cable: The orange LED flashes four times.
CUSTOMIZING THE ESC
To begin, connect the ESC battery wires to a charged battery, then connect the BEC wire
3pin wire to the program card "S+-" port ( 3pin port). Turned on the ESC , the
programming card will automatically read the ESC settings, and the setting items of the
programming card will display 1 to 15 successively, indicating that the connection is
successful. You can start programming ESC. (if it is not displayed, it means that the
connection is unsuccessful, please try to turn off ESC repeatedly, reconnect the
programming card and turn on ESC again until it is successful) TIPS! Program сard is done
using the 4 buttons below on the led, The function of each button start from right hand
side are ITEM, VALUE, OK and RESET.
Please refer to the menu below to program the function settings you need.
"ITEM" button-----------------go to next item to select.
"VALUE" button---------------go to next value select.
"OK" button-------------------go to conrm your select.
"RESET" button----------------go back to factory setup.
Program Manual
Low Voltage Cut-Off: The function is mainly to prevent the lithium battery pack from over discharging. When using lithium battery pack, please set the suitable value
for low-voltage protection as your like. WARNING: Never use the default value "Non-protection" for lithium battery!
Value
(2) (3)
Item
1.Low Voltage Cut-off 3.1V Slow 2.9V Slow 2.7V Slow
2.Start Mode(Punch) Level 3 Level 1 Level 6
3.Max. Brake Force 50% 25% 75%
4.Max. Reverse Force 25% 50% 75%
5.Neutral Range
9% 6% 12%
120 ⁰С Stop 135⁰С Stop 150⁰С Stop
6.Motor Overheat Protection
7.ESC Overheat Protection 105⁰С Stop 95⁰С Stop 105⁰С Slow
Forward/ Forward/ Forward/
8.Running Mode
Reverse/ Brake Reverse
Brake
9.Drag Brake Force 0% 5% 10%
10. Boost Timing
11.Turbo Timing
12.PWM Frequency
8K 2K 4K
13.Brake PWM Frequency
1KHz 400Hz 600Hz
14.Motor Rotation CCW CW
15.BEC Voltage
6V 7.4V
16.Model Racing
Drift
Underscore letter indicate factory default settings, (No.1-9) are applicable to brushless ESC, (No.1-16) are applicable to sensored ESC .
The program card are common use, The BEC voltage selection of this ESC project 15 is fixed at 6V
# KN-ELITE-PRG-01
(4) (5) (6) (7) (8)
Disable 3.4V Slow 3.1V Stop 2.9V Stop 2.7V Stop
Level 2 Level 4 Level 5
100% Disable
100%
1% 3%
120⁰С Slow 135⁰С Slow 150 ⁰С Slow Disable
95⁰С Slow Disable
20% 30%
0⁰ - 60⁰
0⁰ - 60⁰
12K 16K 24K 32K 48K
800Hz 2K 4K
EN
(9)
3.4V Stop