Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. Sunex Tools Manuels
  4. Rangement des outils
  5. 8045WH
  6. Mode d'emploi

Sunex Tools 8045WH Mode D'emploi

Masquer les pouces
Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
SUNEX
TOOLS
OPERATING
MANUAL
Read and follow all instructions in User's Manual. It is the responsibility of the owner to make sure all personnel read
this manual prior to using the device. It is also the responsibility of the device owner to keep this manual intact and
in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact Sunex
Toolso for replacements. If the operator is not fluent in English, the product and safety instructions shall be read and
discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that
the operator comprehends its contents.
PARTS
LIST
Examine box contents, then proceed with following instructions.
Locking
Drawer
Assembly
Bottom
Tray
WARNING
AWARNING
Readand follow all instructions in User's Manual. • Do not load carts beyond
rated capacity (500 lbs.). • Lock lid and drawers before moving. • Applybrake
on locking casters anytime cart is in place. • Units can tip or fall causing
damage or personal injury. • Cart is designed to roll easily on flat surfaces
and should not be used on uneven or inclined surfaces. • Do not open more
than one loadeddrawer ata time. • Do not stand on or step in drawers. • Keep
children away from unit. • Wear gloves when lifting edges. • Failureto heed
these warnings may result in personal injury and/or property damage.
WARNING:
This product can expose you to chemicals
including nickel, which is known to the State of California to
cause cancer and birth defects or other reproductive
For more information go to www.P65Warnings.ca.gov.
8045WH
HEAVY-DUTY
INCLUDES
Legs
(Attached to Legs)
Side
Work
Bench
Pry Bar
Holder
harm.
5 DRAWER
PRY
BAR
HOLDER
Keys
Non-Locking
Casters
Liners
(1) Bottom
(3) Long Drawers
(1) Top Tray
(2) Short Drawers
(I) Side Shelf Rubber
M6x40 Bolts,
Washers,
(8 Pcs. Bolts,
and Nuts, 16 Washers)
TOOLS
Rubber
Mallet
Table
or Workbench
MODEL
8045WH
SERVICE
AND
SIDE
WORK
Locking
(2)
Casters
Long Drawer
Short
Drawer
Handle
(2)
Handles
Shelf
Mat
& Nuts
Spring
Washer
Drawer
Screws
NEEDED
Phillips
Head
10mm
Wrench
Screwdriver
2 People
O Copyright 2019, Sunex Toolse
rev. 04/10/19
CART
BENCH
(2)
(4)
Handle
(20)
loading

Manuels Connexes pour Sunex Tools 8045WH

Sommaire des Matières pour Sunex Tools 8045WH

  • Page 1 SUNEX MODEL 8045WH HEAVY-DUTY 5 DRAWER SERVICE CART INCLUDES HOLDER SIDE WORK BENCH TOOLS OPERATING MANUAL Read and follow all instructions in User's Manual. It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of the device owner to keep this manual intact and in a convenient location for all to see and read.
  • Page 2 Locking Drawer Assembly. Tighten bolts until parts fit together firmly. Repeat steps 1 and 2 for other end of cart, using remaining side accessory. Pry Bar Table Holder Workbench 8045WH rev. 04/10/19...
  • Page 3 Using a rubber mallet, hammer the casters into place until the stem is no longer visible. Repeat with other casters. Ensure that both locking casters A NOTE on same of the cart. Once casters are installed, stand cart upright. Assembly is complete. 8045WH rev. 04/10/19...
  • Page 4 2" Small Right Drawer without Slides (White) 8045WH2D 2" Drawer (White) RS8045PF Plastic Feet (Set of 4) 4" Drawer (White) 8045WH4D RSDECAL02 Black Decal for 8045WH Warning Label (not shown) RS8045WL 8045WH6D 6" Drawer (White) 8007WH Bottom Tray (White) 8045WH...
  • Page 5 SUNEX MODELO 8045WH CARRITO DE SERVICIO PARA SERVICIO PESADO 5 CAJONES TOOLS SE INCLUYE UN SUJETADOR PARA BARRA APALANCAMIENTO Y UN BANCO DE TRABAJO LATERAL MANUAL DE OPERACIÖN Lea y comprendatodas las instrucciones. Hacercaso omiso al seguir todas las instruccionesalistadas a continuaciån podria oca- sionar el choque eléctrico, incendio, explosionesy/o lesionespersonalesserias.
  • Page 6 Apriete los pernos hasta que las piezas se encajen firmemente. Repita los pasos 1 y 2 para el Otro extremo del carrito, usando el accesorio lateral restante. Sujetador Mesa o banca la barra de trabajo apalancamiento 8045WH rev. 04/10/19...
  • Page 7 Repita los pasos con las demås rodajas. Asegürese que ambas rodajas A NOTA de seguridad estén del mismo extremo carrito. Una vez que estén instaladas Ias rodajas, coloque el carrito en posiciön vertical. El ensamblado estå terminado. 8045WH rev. 04/10/19...
  • Page 8 I'État Ia Californie comme causant Ie cancer et des Table ou établi 2 personnes anomalies congénitales ou d'autres effets nuisibles sur Ia reproduction. Pour plus amples informations, aller O Copyright 2019, Sunex Tools@ www.P65Warnings.ca.gov. 8045WH rev. 04/10/19...
  • Page 9 Serrez Ies boulons jusqu'ä ce que Ies piéces s'adaptent ensemble fermement. Répétez Ies étapes I et 2 pour I'autre extrémité du chariot, utilisez l'accessoire latéral restant. Support Table barre de levier établi 8045WH rev. 04/10/19...
  • Page 10 Répétez avec les autres roulettes. Assurez-vous que les deux A REMARQUE roulettes de blocage sont sur la méme extrémité chariot. Une fois que les roulettes sont installées, mettre le chariot å l'endroit. L'assemblage est complété. 8045WH rev. 04/10/19...