Sunex Tools 8516 Mode D'emploi

8516
HYDRAULIC SHOP
• 10-1/2" - 12" (adjustable
• 28-1/2" - 33" (adjustable
• High-polished chrome finish
• Slip-resistant adjustable
• Vinyl padded adjustable
Tools Needed:
#2 Phillips Screwdriver
1 Omm Wrench
1/4" Dr. Ratchet
5mm Hex Bit Socket
Bolt Kit:
4 - M6 x 40mm Hex Bolt
8 - M6 x 41mm Bolt
12 - M6 Nylon Nut
Assembly Instructions:
Step I:
Place one of the legs (#12) into the aluminum bracket holder (#6)
aligning the holes. Insert one of the M6x40mm hex bolts through
the aligned holes, turn the aluminum bracket over so the threads
of the bolt are facing up, then place the round metal disc (#10)
over the single bolt. Fasten using the M6 nut. Do not completely
fasten at this time. Continue the above steps until all four legs
are mounted into the aluminum
Step 2:
Turn the bar stool over onto all four legs.
step 3:
Place the large round support ring (#15) INSIDE all four legs
aligning the holes. Insert one of the M6x41 mm bolts through the
aligned holes. Fasten using the M6 nut. Repeat this process
the remaining three legs. Do not completely fasten!
Step 4:
Place the smaller round support (#7) on the OUTSIDE of all four
legs aligning the holes. Insert one of the M6x41 mm bolts through
the aligned holes. Fasten using the M6 nut. Repeat this process
with the remaining three legs.
step 5:
Completely tighten all bolts!
step 6:
Insert the hydraulic cylinder (#4) into the aluminum bracket (#6).
The orange portion of the cylinder will be facing up when
inserted correctly.
step 7:
Place the seat (#2) over the hydraulic cylinder. Sit on the seat to
ensure that the metal plate is secure on the hydraulic
Step 8:
Place the "L" shaped back supports (#3) into the back of the
seat. (Note: the back supports can only be inserted from one
direction.) Also make sure the screws are completely loosened
before inserting. Repeat the same step on the opposite side.
step 9:
Place the cushioned back support (#1) over the "L" shaped
supports. Note that the push buttons
the back cushion will slide all the way down.
step 10:
Go back and completely tighten all fasteners
A WARNING: This product can expose you to chemicals
including nickel which is known to the State of California to
cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
California93120 Compliant f or Formaldehyde
STOOL
back)
height)
feet allow for leveling on uneven surface
backrest for ultimate comfort
I Parts List:
Back Support
1
2. Seat
3. "L" Shaped Support
4. Hydraulic Cylinder
5. Bolt M6 x 40
Connector
6.
7. Ring
8. M6 Locking Nut
bracket.
cylinder.
must be depressed
and support
Replacement
RS8516SEAT
Bolt M6 x 41
9.
10. Connecting Plate
RSHBSSL
11 Locking Nut M6
RSHBSBK
12. Legs
RSHBSHC
13. Locking Nut M6
RSHBSFT
14. Bolt M6 x 41
15. Ring
1
2
3
4
with
5
6
7
8
9
10
11
12
13
before
14
15
SUNEX
TOOLS
Parts Available:
Replacement Seat Cushion
Plate with Seat Lever
Bolt Kit
Hydraulic Cylinder
Feet (Set of 4)
O
O Copyright 2018, Sunex Tools@
Rev. 10/24/18