T&S SB-36 Manuel Du Propriétaire

T & S Equipment
2999 North Wayne St., Angola, IN 46703
Ph: 219-665-9521
New area code (260) in 2002
Website: www.tseq.com
Ergonomic Solutions
,$Hardwyé Kii
årranv
CONCRETE HARDWARE KIT (standard)
The following tools/hardwareare requiredfor installingyour priorto authorization froma factoryrepresentative.
speed bump.
SB-36-CK KIT INCLUDES:
4 - 1/2" x 6" lag bolt for each hole
8 - 1/2" washers for each lag bolt
4 - 1/2" anchor sleeve for each
SB-108-CK KIT INCLUDES:
5 - 1/2" x 6" lag bolt for each hole
10 - 1/2" washers for each lag bolt
5 - 1/2" anchor sleeve for each bolt
CUSTOMER SUPPLIES:
1 - High-speed hammer drill 3/4" masonry bit
1 - Impact wrench or heavy ratchet 3/4" socket
ASPHALT HARDWARE KIT
The following tools/hardware are required for
speed bump.
SB-36-AK KIT INCLUDES:
4 - 12" long steel spikes
2 - 72" long pieces of Butyl tape
SB-108-AK KIT INCLUDES:
5 - 12" long steel spikes
2 - 108" long pieces of Butyl tape
CUSTOMER SUPPLIES:
1 - Sledge Hammer
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected prior to
shipment. However, it is possible that the unit may incur damage
during transit. If damage is noticed when unloading, make a note
of it on the BILL OF LADING. Remove all packing and strapping
material, then inspect the unit again for damage. IF DAMAGE IS
EVIDENT, FILE A CLAIM WITH THE CARRIER IMMEDIATELY!
WARRANTY
This product is warranted for 30 DAYS from date of
purchase to be free of manufacturing defects in material and
workmanship. The manufacturer's obligation hereunder is lim-
ited to repairing such products during the warranty period,
provided the product is sent prepaid back to the factory.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or
misuse of the product, use or application contrary to installation
Company
Fax: 219-665-1339
bolt
installing
your
Revised 08-01
A company dedicated to solving ergonomic and material
handling problems since 1955.
OWNERS
MANUAL
SPEED BUMP MODEL
Assem io
instructions, or disassembly, repair or alteration by any person
ASSEMBLY INSTRUCTIONS
CONCRETE (standard)
1.) Position the speed bump in its intended position and using
its predrilled holes as templates, mark the location of each
hole on the road surface.
2.) Remove the speed bump. Using high speed hammer drill
with a 3/4" masonry bit, drill a hole at each marked location
to a depth of 3-1/2" below the road surface.
3.) Insert a anchor sleeve into each hole (large sleeve opening
on top). Tap the sleeves into the holes with a hammer so that
the sleeves are set flush with the surface.
over each sleeve hole.
Make sure the substrates are thoroughly clean and dry.
4.)
Reposition the speed bump in its installation position. Apply
firm hand pressure. Slip a washer onto a lag bolt, insert the
bolt through a predrilled hole in the speed bump, align over
anchor sleeve and tighten the bolt about three-quarter of the
way with the 3/4" socket. Repeat for each hole in the speed
bump. Finish tightening each bolt until just snug. DO NOT
OVER TIGHTEN! Excessive tightening may damage the
speed bump and void the product warranty.
ASSEMBLY INSTRUCTIONS
ASPHALT, HIGH USE AREA'S,
PERATURES OVER 11
1) Adhere the Butyle tape to the under structure of speed
bump length wise.
2) Place speed bump in desired position.
3) Insert spike through pre-drilled hole. DO NOT HOLD SPIKE
WHILE HAMMERING! Drive spike into ground until flush
with speed bump.
SPEED BUMP • MODEL
29-126-102
SB-36 & SB-108
Place a washer
OR LOCATIONS WITH TEM-
SB-36 & SB-108