Pulsar DL FLOWER Manuel D'instructions
Les langues disponibles
Les langues disponibles
Liens rapides
SPECS
Chamber Size: 0.25 g
Battery Capacity: 1200 mAh
Temperature Range: 320 - 430°F (160 - 221°C)
Charging: USB-C
KIT INCLUDES
1x DL Flower
1x USB-C Charging Cable
1x Cleaning Brush
2x Mouthpiece Screens
CHARGING
Before using the DL Flower, fully charge the device using the USB-C charging cable and a standard charging brick.
You will see the battery indicator lights flash when the battery is charging, and the battery indicator lights will
represent the battery level. When the battery reaches 100%, the device is fully charged, and battery indicator
lights will turn off. The device does not have pass-through functionality.
BATTERY INDICATOR
4 lights 75 - 100%
3 lights 50 - 75%
2 lights 25 - 50%
1 light
0 - 25% (Charge)
LOADING THE CHAMBER
With the device off, remove the mouthpiece. Fill the chamber to the top with finely ground material. It should fill the
chamber completely, but not be packed too tightly. Depending on your material, 0.25 g should be enough. Replace
the mouthpiece once the chamber is packed.
POWER ON/OFF
To power the device on or off, quickly press the button 5 times. The device will vibrate to let you know it is turning
on or off. It will automatically start heating once it has been turned on.
TEMPERATURE SELECTION
The DL Flower has a temperature range of 320 to 430°F (160 - 221°C). Use the up and down buttons to select your
preferred temperature in increments of 5 degrees. Once your preferred temperature is selected, the device will
vibrate once it has hit that temperature. You can increase or decrease the temperature at any time during the
session. The device will vibrate again to let you know the new temperature has been reached. You can convert the
temperature read out to Celsius by holding the power button and the down button at the same time for 2 seconds.
VAPING SESSION TIMER
To adjust the session duration, hold down the power button for 2 seconds once the device is on. You can then
adjust the session duration at any time between 3 minutes (180 seconds) to 5 minutes (300 seconds) in
increments of 30 seconds. The display will only show the number of seconds for the session, please refer to the
chart below for minutes.
180 - 3 minutes
210 - 3:30 minutes
240 - 4 minutes
270 - 4:30 minutes
300 - 5 minutes
PAGE 1
INSTRUCTION
MANUAL
PulsarShop.com
TEMPERATURE/
BATTERY
INDICATOR
PU-0707-24
Manuels Connexes pour Pulsar DL FLOWER
Sommaire des Matières pour Pulsar DL FLOWER
- Page 1 TEMPERATURE SELECTION The DL Flower has a temperature range of 320 to 430°F (160 - 221°C). Use the up and down buttons to select your preferred temperature in increments of 5 degrees. Once your preferred temperature is selected, the device will vibrate once it has hit that temperature.
- Page 2 INSTRUCTION MANUAL VAPING Once the device hits the selected temperature it will vibrate to let you know it is ready. At this point you can begin vaping. We recommend taking longer slower pulls to get the most out of the experience. Once you have finished the session, use the included stir tool to stir the material or discard it once it has been fully used.
- Page 3 SÉLECTION DE LA TEMPÉRATURE Le DL Flower offre une plage de température de 160 à 221 °C (320 à 430 °F). Utilisez les boutons haut et bas pour sélectionner la température souhaitée par incréments de 5 degrés. Une fois la température sélectionnée, l'appareil vibre dès qu'il l'atteint.
- Page 4 INSTRUCTION MANUEL VAPOTAGE Une fois la température sélectionnée atteinte, l'appareil vibre pour vous indiquer qu'il est prêt. Vous pouvez alors commencer à vapoter. Nous vous recommandons de vapoter plus lentement et plus longtemps pour une expérience optimale. Une fois la session terminée, utilisez le mélangeur fourni pour remuer le contenu ou jetez-le une fois utilisé.