Philips LIGHTOLIER LyteCaster Instructions D'installation

Page 1 of 2
This luminaire IS Intended for Installation In accordance With the National Electric Code and Loca Regulations. To assure full
compliance with local codes and regulations, check with your local electrical Inspector before installation To prevent electrical
shock, turn off electricity at fuse box before proceeding
CAUTION. Use only reflector trim sections provided by Philips Lightolier. Use of other manufacturers reflector trims or light
engines may void the Underwriters
A. MOUNTING BAR POSITION:
determine mounting bar position
building construction / lighting
mounting bar position needs
needed proceed to B.
can be changed 90' from original position
and rotating the spinner brackets
Mtg bars supplied with integral
B. FRAME—IN—KIT(for suspended
I. cut appropriate dia. hole in tile (see below * ), then orient
mtg bars on frame to desired
required length then tighten mtg. bar locking screws(4
places) position fixture directly on ceiling tile then secure to
T—Bar grid using drill point screws
bars SEE FIG 3. Fixture can be additionly
wire ( provided by others) to T—bar and building structure.
C. FRAME—IN—KIT. (for wood joist)
I) Line up bottom edge of hinged mounting bar with bottom
of joist and fasten in place
with frame—in—kit (depends on SKU) see FIG 4. Then swing
up frame an extend mtg bars
secure to joist. Finally tight mtg bar locking screws (ref
For centering and fixture
on collar. see FIG IA.
For tight joist spacing Channel
seperated and shortened . see FIG 6.
D WIRE IN:
I) open hinged J—box door then wire supply leads WHITE to
either White or Blue(depending on SKU) neutral supply lead.
Black or Brown to hot (120 or 277v) Bare copper ground
lead to supply ground using wire nuts(local
For 0—10V dimming frames use
for the dimming control.
then close door.
E. Ceiling (By others)
Install plaster board or other
can be cut either before or after ceiling is secured to joists.
Mounting frame can be used
cutout see below *
F. AIRSEAL INSTALLATION(optional)
Install a bead of silicone caulking
frame. Frames are tested in accordance
2 cubic feet per minute@ 75 Pa) and comply with with WESC
& MEC when installed as instructed.
G. DRIVER REPLACEMENT: FIG 5
MUST be performed by a qualified
1) Turn off power to Luminaire.
2) Remove trim assembly by pulling down on flange and
CCW for 5 & 6 in. trims (straight down on
slightly turn
4 in trims).
3) Disconnect the connector on trim assembly.
4) Remove wing nuts that secure internal
bring the door and driver assembly
then disconnect wiring.
5) to reinstall driver use the reverse of step 4 above.
* CEILINGCUTOUT: 4 IN APERTURE: 4} " (111mm)
5 INAPERTURE: 51 " (140mm)
6 IN APERTURE
NOTE: For luminaires with dimming capatibi/ity:
Reference dimming
compatible dimmers.
0 2016 Philips Lighting Hold-ng B.V. All rights reserved.
\oww.philips.com/ uminaires
IS:L RAE Feb-16 revD page I of 2
INSTALLATION INSTRUCTIONS
Read and understand these Instructions before installing luminaire.
Retain these instructions
Laboratories listing and could constitute
for frame—in—kit based
application. See below if
to be changed. if no change
I. Mounting bar orientation
by removing bars
see FIG.2.
nails or screws.
ceiling)
position. Extend mtg. bars
provided with the mtg
secured with saftey
with screws or nails provided
to reach opposite joist an
alignment use alignment notch
mounting bar can be
hardware item).
the GREY and VIOLET leads
Place all connections in jbox
dry type ceiling. Hole in ceiling
as a cutting guide. Ceiling
between ceiling opening
with ASTM E283(max
electrician.
jbox door and
through opening in ceiling
: " (162 mm)
frame specification sheets (LED-DIM) for a list of
Instruction Number I S:L
FOR FRAME-IN-KITS
for maintenance reference
a fire hazard
MOUNTING BAR
is
FIG. I
to
FRAME MOUNTING
SCREWS
MTG. BAR LOCKING
SCREWS
and
FIG 6
WINGNUT
LyteCaster LED Low Profile FIK
SPINNER BKT
ALIGNMENT
NOTCH
FIG. 2
MTG. BAR FOOT
AGAINST T-BAR
FIG. 3
T-BAR GRID
FIG 4
NTERNAL J-BOX
DRIVER
CEILING
FIG. 5
NOTE DRIVER MAY BE ON
EITHER SIDE OF J-BOX
PHILIPS
RAE
IA
SHOWN
DOOR
OPENING
DOOR