T&S TT-18 Manuel
Les langues disponibles
Les langues disponibles
T & S Equipment
2999 North Wayne St., Angola, IN 46703
Ph: 219-665-9521
Website: www.tseq.com
Ergonomic
Solutions
Contents
Safety Precautions
Recerving Instructions
Warranty
Exploded Parts Drawing for,TT-18
Parts List for IT-18
SAFETY
PRECAUTIONS
Read owner's manual completely before operating unit!
• Do not exceed maximum capacity of 1,000 pounds for the
TT-18
and 300 lbs. for TV-18-PED.
• Ensure unit is evenly loaded for maximum stability.
• Do not sit or stand
on Turntable.
• Use Turntable only on a flat, level surface.
RECEIVING
INSTRUCTIONS
Every unit is thoroughly tested and inspected prior to
shipment.
However, it is possible that the unit may incur
damageduring transit. If damage is evident while unloading,
note it on the BILL OF LADING. Remove all packing and
strapping materials. Inspect unit again, checking for any
damage.
IF DAMAGE IS EVIDENT, FILE A CLAIM WITH HE
CARRIER
IMMEDIATELY!
TT-18-PED
Company
Fax (219)665-1339
TT-18
ITEM
1
2
3
Revised
12-00
A company dedicated to solving ergonomic and material
handling problems since 1955.
OWNERS
MANUAL
MANUAL
TURNTABLE
MANUAL
TURNTABLE
MODEL
TT-18-PED
Installation
InstructidhS
1
Installation Instructions for TT+I@+PED
.1
HéiGht Adjustment
Exploded parts Drawing for.TT-18-PED „„3
Parts List for TT-18-PED
WARRANTY
This product is warranted for 90 DAYS from date
of purchaseto befreeof manufacturingdefects in material
and workmanship. The manufacturer's obligation
hereunderis limitedto repairingsuchproductsduringthe
warranty period,providedthe product issent prepaidback
to the factory.
This warrantydoes notcover normalwear of parts
or damage resulting from any of the following: negligent
use or misuse of the product, use or application contrary
to installation instructions, or disassembly, repair or
alteration by any person prior to authorization from a
factory representative.
PARTS
BENCHTOP TURNTABLE (MODEL IT-18)
DESCRIPTION
ENGINEER
To
Plate
201-130-16
Bearin
Assembl
20-110-007
Top Plate Bolts
TT-FAS
20-126-101
• MODEL TT-18
WITH PEDESTAL
for TT-18
-1
1
2
LIST
NO.
PART NO.
QTY.
TT-TPLT
TT-BRASSY
TT-FAS
•
2
g
1
1
4
1
Table des Matières
Sommaire des Matières pour T&S TT-18
- Page 1 TT-18 Recerving Instructions Installation Instructions for TT+I@+PED Warranty HéiGht Adjustment Exploded Parts Drawing for,TT-18 Exploded parts Drawing for.TT-18-PED „„3 Parts List for TT-18-PED Parts List for IT-18 WARRANTY SAFETY PRECAUTIONS This product is warranted for 90 DAYS from date...
- Page 2 Installation Instructions For installation you will need the following: 1) Drilling tools 2) Socket wrench (for a M6-1 .O and 10-24 unc HHCS bolt) 3) Four bolts (10-24 unc HHCS or equivalent) PLATE Remove the top plate from the bearing assembly Step 1: GUIDE HOLE...
- Page 3 HEIGHT ADJUSTMENT The TT-18-PED can be adjusted from 21" to 32". To adjust the height (never adjust with load on table), hold the turntable with one hand (mayrequirea second person), loosenthe heightadjustmenthandleon the side, and raise or lower to the desired height. Once the desired heighthas been met, tighten the height adjustment back down. The TT-18-PED is now ready to use.
- Page 4 • No exceda la capacidad måxima de 453 kgs. para TT-18 y material y mano de Obra. La obligaciön del fabricante estå 136 kgs. para TT-18-PED limitada a reparar tales productos durante el periodo de •...
-
Page 5: Vista Superior
Instrucciones de Instalaci6n Para la instalaciön se necesitara: 1) Herramientas de taladro 2) Llave inglesa (para M6-1 .Oy tornillos de 10-24 unc HHCS) 3) Cuatro tornillos (10-24 unc HHCS o equivalente) PLATO SUPERIOR AGUJERO DE GUIA Quite eI plato superior del ensamble Paso •... -
Page 6: Identification De Partes
DE ALTURA El TT-18-PED se puede ajustar de 21" a 32". Para ajustar la altura (nunca la ajuste con carga en la mesa), aguante el banco con una mano (se podria requerir una segunda persona), afloje la manivela de ajuste de altura en el lateral, y eleve o descienda hasta la altura deseada. -
Page 7: Précautions De Sécurité
Ia facture de transport. Retirertoutle matérield'empaquetageet lessangles,et inspecter Ilunitéde nouveaupourconstatertoutdommage.Si ledommage est évident, remplir immédiatement une plainte avec Ie transporteur! TT-18 LISTE DES PIÉCES POUR TABLE TOURNANTE ÉTABLI MODÉLE TT-18 NO. D'ARTICLE QTÉ. DESCRIPTION NO. DINGENIEUR NO. DE PIÉCE Plateau Supérieur 201-130-16... -
Page 8: Vue Du Dessous
Instructions Dinstallation Pour Ilinstallation, vous aurez besoin de ce qui suit: 1)Outils de perqage 2)Clé å molette (Pour des boulons M6-1.Oet 10-24 unc HHCS) 3)Quatre boutons (10-24 unc HHCS ou équivalent) PLATEAU SUPÉRIEUR Démarche No. I: Retirez Ie plateau supérieur de l'assemblage å paliers TROU GUIDE •... - Page 9 Ilunité doivent toucher le sol afin de réduire le risque de basculement de l'unité. AJUSTEMENT DE LA HAUTEUR Le modéle TT-18-PED peutétreajustéde 53 cm 81cm. Pourajusterla hauteur(nejamaisajusteravecun chargement surla table),tenirla tabledune main(unesecondepersonne peutétrenécessaire), desserrer l a poignée d'ajustement dehauteursurlecåté,et monter o udescendre l'unitéä la hauteur d ésirée. U nefoisquela hauteur v oulue est atteinte,serrerla poignéed'ajustement.
- Page 10 - NOTES...
- Page 11 - NOTES -...
- Page 12 Material Handling Problem Solvers Scissor Lift Table Pallet Server S XII High Rise Lift Time is money. Increased productivity equals greater profitability, cost minimization and worker compatibility.GErgonomic products will, assist you with your production and safety goals. Mobile Lift & Tilt Drum Carrier/Rotator Work...