SkyLink WB-602 Instructions D'installation

INSTALLATION INSTRUCTIONS
Wireless Wall Control
Model : WB-602
Congratula�ons on your purchase of the Skylink Wireless
Wall Control model WB-602. This Wall Control is
designed to operate the Skylink Atoms Garage Door
Opener series. You will find the installa�on to be simple
and be able to get the system up and running with li�le
effort.
SAFETY INFORMATION
This device complies with Part 15 of the FCC Rules.
Opera�on is subject to the following two condi�ons: (1)
This device may not cause harmful interference, and (2)
This device must accept any interference received,
including interference that may cause undesired
opera�on.
WARNING:
Changes or modifica�ons to this unit not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This device complies with Industry Canada license-ex-
empt RSS standard(s). Opera�on is subject to the
following two condi�ons: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired opera�on of the device.
Package Contents
A
B
C
D
Parts Descrip�on Quan�ty
Wireless Wall Control 1
A
Drill Template 1
B
Wall Anchor
C 2
D Screw
2
Sec�on 1 – Overview
1. Open and close bu�on
2. Light / Auto-close bu�on
1
2
WARNING:
- Wall Control must be installed within sight of the
garage door, out of reach of children, at a
minimum height of 5 feet (1.5m), and away from
all moving parts of the door.
- Be sure power is not connected before installing
the Wall Control.
- Wall Control should only be ac�vated when the
door can be seen clearly, is properly adjusted, and
there are no obstruc�ons to door travel.
- Always keep the garage door in sight un�l
completely closed. Never permit anyone to cross
the path of the closing garage door.
Sec�on 2 – Installa�on of the Wall Control
Note: The ba�ery for the Wall Control is included.
1. Place the screwdriver perpendicular to the Wireless
Wall Control at the opening posi�on.
900
1
900
Opening posi�on
Sec�on 2 – Installa�on of the Wall Control
2. Li� the cover using the screwdriver for leverage. Then
open the cover of the Wireless Wall Control.
2
1
2
3
3. Drill holes as marked on the drill template, then screw
the wall anchor to the wall.
4. Mount the Wireless Wall Control with the two screws
provided.
3
4
Y
X
5. Reassemble the case of the Wireless Wall Control.
When reassembling the case of the Wireless Wall
Control, make sure that position X aligns with position Y.
Sec�on 3 - Change the Ba�ery
(cont)
1. Open the Wireless Wall Control (refer step 1,2 of
sec�on 2)
Open
2.Replace the ba�ery by gently pushing out the old
ba�ery from the ba�ery slot and replacing it with a
new ba�ery.
CR2032
3. Reassemble the case of the Wireless Wall Control
(refer to step 5 of sec�on 2).
Sec�on 4 – Programming the Wall Control
1. Set the garage door opener you want to be paired with
the WB-602 into programming mode. Please refer to
the User's Instruc�ons for the garage door opener.
2. A�er the opener is in programming mode, press the
bu�on on the wall console to transmit the signal.
3. The opener will exit programming mode if the
programming process is successful.
4. The Wall Console is ready to be used to operate that
opener/receiver.
Sec�on 5 - Opera�on of the Wall Control
1. To open/close the Garage Door: Press the open/close
bu�on once [Bu�on 1].
2. To toggle the light on/off: Press the Light / Auto-close
bu�on [Bu�on 2].
3. Se�ng Auto-close mode:
By default, the Wireless Wall Control is set to normal
mode. If you want to set Auto-close mode, follow
these steps:
Press and hold the Light / Auto-close bu�on [Bu�on 2]
for 5 seconds. The LED will turn on a�er about 3
seconds. A�er setup, the opener will auto-close the
door a�er 3 minutes. Repeat the above opera�on to
exit the auto-close mode.
Sec�on 6 – LED Light Indica�on
Auto-close mode The red LED will turn on
while transmi�ng the signal.
Normal mode
The red LED will flash while
transmi�ng the signal.
Ba�ery.