Les langues disponibles

Les langues disponibles

Liens rapides

4344709
4262082
LEDVANCE HIGH BAY
Installation Instructions
PERFORMANCE CLASS
HAZARDOUS LOCATION HIGH BAY
The Performance Class Hazardous Location High Bay is
built for dependable operation in environments with
flammable vapors, gases, or combustible dust. Perfect
for chemical plants, petroleum facilities, marine
terminals, and other hazardous industrial sites. Its robust
design delivers powerful, long-lasting illumination under
the toughest conditions.
For warranty coverage, please register at
Please Read All Instructions Before Attempting Installation
TO PREVENT PERSONAL INJURY OR PRODUCT DAMAGE, ONLY LICENSED ELECTRICIANS SHOULD PERFORM
ALL INSTALLATION SERVICES.
• TO AVOID ELECTRIC SHOCK OR COMPONENT DAMAGE, DISCONNECT POWER BEFORE ATTEMPTING
INSTALLATION OR SERVICING.
• THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC) AND ALL
APPLICABLE FEDERAL, STATE AND LOCAL ELECTRIC CODES AND SAFETY STANDARDS.
• USE ONLY UL (OR OTHER NTRL) APPROVED WIRE FOR INPUT/OUTPUT CONNECTIONS. MINIMUM SIZE 18 AWG
OR 14 AWG FOR CONTINUOUS RUNS. SUPPLY CONDUCTORS MUST BE RATED TO MIN 90
• SUITABLE TO INSTALL IN A HAZARDOUS ATMOSPHERE, EXCEPT WHERE THE AMBIENT TEMPERATURE
EXCEEDS THE RATED OPERATING TEMPERATURE OF THE FIXTURE.
• USE CAUTION WHEN HANDLING THIS PRODUCT DURING OR AFTER OPERATION AS IT MAY BECOME HOT AND
CAUSE BURNS. DISCONNECT PRODUCT AND ALLOW COOLING PRIOR TO SERVICING.
• ANY ALTERATION OR MODIFICATION OF THIS PRODUCT IS EXPRESSLY FORBIDDEN AS IT MAY CAUSE
SERIOUS PERSONAL INJURY, DEATH, PROPERTY DAMAGE AND/OR PRODUCT MALFUNCTION.
• TO PREVENT PRODUCT MALFUNCTION AND / OR ELECTRICAL SHOCK THIS PRODUCT MUST BE PROPERLY
GROUNDED.
• CAUTION - RISK OF FIRE
• THIS LUMINAIRE IS DESIGNED TO OPERATE IN AMBIENT TEMPERATURES RANGING FROM -40°F TO +131°F
(-40°C TO +55°C) AND IS RATED FOR WET LOCATIONS.
• CAUTION: To reduce the risk of ignition of Hazardous Atmospheres, disconnect the luminaire from the AC supply circuit
and determine that the area is free of ignitable concentration before opening. Keep tightly closed when in operation.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Also complies to Canadian standard CAN ICES-005(A)/NMB-005 (A)
Please visit: https://www.ledvanceus.com/fccpart15b
4344709
www.ledvanceUS.com/warranty
WARNING
o
C
Table des Matières
loading

Sommaire des Matières pour Ledvance HIGH BAY

  • Page 1 LEDVANCE HIGH BAY Installation Instructions PERFORMANCE CLASS HAZARDOUS LOCATION HIGH BAY The Performance Class Hazardous Location High Bay is built for dependable operation in environments with flammable vapors, gases, or combustible dust. Perfect for chemical plants, petroleum facilities, marine terminals, and other hazardous industrial sites. Its robust design delivers powerful, long-lasting illumination under the toughest conditions.
  • Page 2: Safety Precautions

    HAZHBP/150UNVD850/GRE: 0°C to +40°C, T5 HAZHBP/200UNVD850/GRE: 0°C to +40°C, T5 HAZHBP/080UNVD850/GRS25E: 0°C to +40°C, T6 HAZHBP/150UNVD850/GRS25E: 0°C to +40°C, T5 Trouble Shooting Checklist Check your power source. • • Check electrical connections List of Parts Included High Bay Luminaire • Accessory: Screw • 4344709...
  • Page 3: Wiring Diagram

    4344709 4262082 Wiring Diagram: 4344709...
  • Page 4 4344709 4262082 Installation Instructions | Ceiling Mount 1. Turn Off Power: Ensure power is switched off at the 3. To open the connection cover of the luminaire, unscrew circuit breaker to prevent electrical shock or other the M8*25 pin using an Allen wrench with torque of 8Nm hazards.
  • Page 5: Installation Instructions

    4344709 4262082 Installation Instructions | Bracket Mount 1. Turn Off Power: Ensure power is switched off at the 3. To open the connection cover of the luminaire, unscrew circuit breaker to prevent electrical shock or other the M8*25 pin using an Allen wrench with torque of 8 Nm hazards.
  • Page 6 4344709 4262082 Installation Instructions | Stanchion Mount - cont. 3. To open the connection cover of the luminaire, unscrew the M8*25 pin using an 5/32” Allen wrench with a torque of 8 Nm. 4. Make the electrical connection using the connection terminals identified on the luminaire terminal block.
  • Page 7 4344709 Magnetically Controlled Switch Magnet Note: The component to adsorb magnet 1. The magnet should be moved horizontally (the light will not work if the magnet is moved vertically). 2. When the magnet leaves the magnetic switch position, the distance should be kept more than 10 centimeters.
  • Page 8 GND ( GREEN ) Retrofit Process LEDVANCE HIGH BAY Series is also for use where Eaton top hats are installed and where LEDVANCE luminaires are needed without opening the existing conduit system. Below Models are applicable in such situation: NAED Code...
  • Page 9 4344709 Retrofit Process - cont. LEDVANCE HIGH BAY Series is is compatible with the following Eaton top hats: Eaton’s Crouse-Hinds-Champ Pendant Ceiling Wall Stanchion Quad Mount APM2 TWM2 QM25 APM3 TWM3 HPM2 Eaton Top Hat Screw provided in package Ledvance luminaire...
  • Page 10: Luminaire Pour Très Grande Hauteur Ledvance

    4344709 4262082 LUMINAIRE POUR TRÈS GRANDE HAUTEUR LEDVANCE Directives d’installation LUMINAIRE POUR TRÈS GRANDE HAUTEUR DE CLASSE PERFORMANCE POUR ENDROITS DANGEREUX Le luminaire pour très grande hauteur de classe performance pour endroits dangereux est conçu pour une opération fiable dans les environnements avec vapeurs inflammables, gaz ou poussière combustible.
  • Page 11: Mesures De Sécurité

    4344709 4262082 Mesures de sécurité : IMPORTANT : VEUILLEZ LIRE ATTENTIVEMENT LES DIRECTIVES D’INSTALLATION AVANT L’INSTALLATION DE CE LUMINAIRE. GÉNÉRAL : Lors de la réception de l'appareil, vérifiez soigneusement qu'il n'y a pas de dommages causés durant le transport et si des dommages sont constatés aviser le transporteur. Conformités et classification environnementales : Ce luminaire convient à...
  • Page 12: Schéma De Câblage

    4344709 4262082 Schéma de câblage : 4344709...
  • Page 13 4344709 4262082 Directives d’installation | Montage en surface M.-À-T. NPT ¾ po-14 1. Couper l’alimentation : s’assurer que l’alimentation 3. Pour ouvrir le couvercle des connexions du luminaire, est coupée au disjoncteur afin de prévenir le choc dévisser avec une clé hexagonale M8*25 à un couple de électrique ou autres dangers.
  • Page 14 4344709 4262082 Directives d’installation| Montage sur support 1. Couper l’alimentation : s’assurer que l’alimentation 3. Pour ouvrir le couvercle des connexions du luminaire, est coupée au disjoncteur afin de prévenir le choc dévisser avec une clé hexagonale M8*25 à un couple de électrique ou autres dangers.
  • Page 15 4344709 4262082 Directives d’installation | Montage à 25° sur poteau (suite) 3. Pour ouvrir le couvercle des connexions du luminaire, dévisser avec une clé hexagonale M8*25 à un couple de serrage 8 Nm 4. Effectuer les connexions électriques en utilisant les bornes identifiées sur le bloc de jonction du luminaire.
  • Page 16: Interrupteur Contrôlé Magnétiquement

    4344709 Interrupteur contrôlé magnétiquement Aimant Note : Le composant adsorbe sur 1. L’aimant devrait être déplacé horizontalement l’aimant (le luminaire ne fonctionnera pas si l’aimant est déplacé verticalement). 2. Lorsque l’aimant quitte la position d’interrupteur magnétique, la distance devrait être maintenue à plus de 10 centimètres. Étiquette collée sur le boîtier Entre-temps, garder une vitesse rapide à...
  • Page 17: Câblage D'urgence

    La série de LUMINAIRES POUR TRÈS GRANDE HAUTEUR de LEDVANCE s’utilise où les rails Eaton sont installés et les luminaires LEDVANCE sont requis sans avoir à ouvrir le système de conduit. Les modèles ci-dessous sont utilisés dans ce cas : Code NAED No de modèle...
  • Page 18: Processus De Modernisation - Suite

    4344709 Processus de modernisation - suite La série de LUMINAIRES POUR TRÈS GRANDE HAUTEUR de LEDVANCE est compatible avec les rails Eaton suivants : Champ d’Eaton Crouse-Hinds Suspension Plafonnier Applique murale Sur montant Montage quad. APM2 TWM2 QM25 APM3 TWM3...

Table des Matières