S+S Regeltechnik Premasgard 814 Modbus Série Notice D'instruction page 15

G
®
PREMASGARD
TECHNICAL DATA
Bus protocol:
Signal filtering:
Ambient temperature:
Electrical connection:
Housing:
Housing dimensions:
Cable connection:
Protective tube:
Process connection:
Protection class:
Protection type:
Standards:
Optional:
ACCESSORIES
ASD - 06
MFT - 20 K
PREMASGARD ® 814x - Modbus
Type ⁄ WG02
®
PREMASGARD 8148 - Modbus
PREMASGARD 8148-Modbus
PREMASGARD 8148-Modbus LCD
®
PREMASGARD 8147 - Modbus
PREMASGARD 8147-Modbus
PREMASGARD 8147-Modbus LCD
Extra charge:
Optional: Cable connection with M12 connector according to DIN EN 61076-2-101
ACCESSORIES
KA2 -Modbus Communication adapter (USB/RS485) for system connection
LA -Modbus Line termination device (with terminating resistor) as an active bus termination
ASD-06
Connection set (included in the scope of delivery), consisting of
2 connection nipples (straight) made of ABS,
2 m PVC hose (soft, UV-resistant) and 4 screws
ASD-07 2 connection nipples (at 90° angle) made of ABS
DAL-01 Pressure outlet for ceiling or in-wall installation (e.g. in clean rooms)
SF-M Metal sinter filter, Ø 16 mm, L = 32 mm, exchangeable,
stainless steel V4A (1.4404)
MFT-20-K Mounting flange, plastic (included in the scope of delivery)
814x - Modbus
Modbus (RTU mode), address range 0...247 adjustable
4 s / 32 s at temperature / humidity
0 s / 1 s / 10 s at pressure
–30...+70 °C
2
0.2 - 1.5 mm , via push-in terminal
plastic, UV-resistant, material polyamide, 30 % glass-globe reinforced,
with quick-locking screws (slotted ⁄ Phillips head combination),
colour traffic white (similar to RAL 9016), housing cover for display is transparent!
126 x 90 x 50 mm (Tyr 2)
cable gland, plastic (M 16 x 1.5; with strain relief, exchangeable, max. inner diameter 10.4 mm) or
M12 connector according to DIN EN 61076-2-101 (optional on request)
PLEUROFORM TM , material: polyamide (PA6), with torsion protection, v
(on request, optional stainless steel V2A (1.4301), Ø 16 mm)
with plastic sinter filter: NL = 235 mm (optional with metal sinter filter: NL = 227 mm)
via mounting flange made of plastic (included in the scope of delivery)
III (according to EN 60 730)
IP 65 (according to EN 60 529) housing only! (PLEUROFORM IP 30)
CE-conformity, electromagnetic compatibility according to EN 61 326, EMC Directive 2014 ⁄ 30 ⁄ EU
three-line display with illumination, programmable, cut-out approx. 70 x 40 mm (W x H),
for display actual humidity, actual temperature and ACTUAL pressure (cyclic)
or a selectable parameter (static)
or an individually programmable display value (The Modbus interface allows
the display to be individually configured in the 7-segment area and in the dot-matrix area.)
see table
Connection set (nipple straight) – (included in the scope of delivery)
Mounting flange plastic (included in the scope of delivery)
Multifunctional duct sensor for
humidity, temperature, pressure, differential pressure and volume flow rate, Deluxe
Measuring ranges
Pressure
– 500...+ 500 Pa
– 500...+ 500 Pa
– 500...+ 500 Pa
Equipped as standard with automatic zero point calibration
– 7000...+ 7000 Pa
– 7000...+ 7000 Pa
– 7000...+ 7000 Pa
with optional automatic zero point calibration (please specify in your order)
Humidity Temperature
0...100% r.H. –35...+80°C
0...100% r.H. –35...+80°C
0...100% r.H. –35...+80°C
0...100% r.H. –35...+80°C
15
= 30 m/s (air), Ø 20 mm,
max
Output Item no.
Display
Modbus 1301- 8144-09 10-20V
Modbus ■ 1301- 8144-49 10-20V
Modbus 1301- 8144-09 50-200
Modbus ■ 1301- 8144-49 50-200
1906- 1200- 0000- 100
1906-1300- 0000- 100
7100 -0060- 3000- 000
7100- 0060- 7000-0 00
7300- 0060- 3000-001
700 0-0050- 2200- 100
7000- 0031-0000- 000
Rev. 2021 - V13
(continued)
on request