Publicité
J U M P + P O W E R B A N K
SE T UP GU ID E
SPECIFICATION
J U MP+ P O WER B AN K (MODEL No: J U M PS P0 1 )
Input C: PD3.0, 5V
3A ; 9V
2A ; 12V
1.5A
Output A: QC3.0, 5V
3A ; 9V
2A ; 12V
1.5A
Output C: PD3.0, 5V
3A ; 9V
2A ; 12V
1.5A
*5V/3A 8412mAh ; 9V/2A 8516mAh ; 12V/1.5A 8615mAh
Qi Output: 5W
Total Output: 18W (8000mAh)
Battery: 3.7V 12000mAh 44.4Wh
HOW TO CONNECT
LED INDICATION
100%
80%
60%
40%
20%
REGULATORY INFORMATION
CONFORMS TO UL STD.62368-1
CERTIFIED TO CSA STD. C22.2 NO. 62368-1
CAN-ICES-3(B)/NMB-3(B)
IC No. 23711-JUMPSP01
FCC Statement (USA)
FCC responsible party: Design Pool LLC, 6150 Washington Blvd, Culver City, CA 90232, USA; Telephone +1 (424) 6034270
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be used with a
minimum distance of 10 cm from all persons. FCC ID: X3QJUMPSP01
CAUTION: Risk of fire and burns. Do not open, crush, heat above 60°C, or incinerate. Follow manufacturer's instructions.
RSS Statement (Canada)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. It should be used
with a minimum distance of 10 cm from all persons. IC: 23711-JUMPSP01
DoC Declaration of Conformity (Europe)
Hereby, Design Pool Limited declares that the product JUMPSP01 is in compliance with Directives 2014/53/EU, 2014/30/EU, 2014/95/CE.
The full text of the EU DoC is available at: nativeunion.com/product-documentation
Manufacturer: Design Pool Limited. 2/F East Town Building, 41 Lockhart Road, Wan Chai, Hong Kong - support@nativeunion.com
EU Importer: Design Pool SAS, c/o The Bureau, 28 Cours Albert 1er, 75008 Paris, France
Qi Wireless Charging
Green LED
Wireless Charging
Green LED flashing
Wireless Charging Alert
- Device not supported
- Foreign object
- Out of center
PERFORMANCE
ENERGETIQUE
5 0 1 4 9 8 5
E P 5 0 1 5 1 4 0
Qi Enable /
Battery check
HOW TO RECHARGE
POSITIONING
IMPORTANT SAFETY INSTRUCTIONS
ENERGY
VERIFIED
WARNING – When using this product, basic precautions should always be
RENDEMENT
followed, including the following:
VERIFIE
1. Read all the instructions before using the product
2. To reduce the risk of injury, close supervision is necessary when the
product is used near children.
3. Do not put fingers or hands into the product.
4. Do not expose power bank to rain or snow.
5. Use of a power supply or charger not recommended or sold by power
pack manufacturer may result in a risk of fire or injury to persons.
6. Do not use the power bank in excess of its output rating. Overload
outputs above rating may result in a risk of fire or injury to persons.
7. Do not use the power bank that is damaged or modified. Damaged or
modified batteries may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
8. Do not disassemble the power bank. Take it to a qualified service person
when service or repair is required. Incorrect reassembly may result in a
risk of fire or injury to persons.
9. Do not expose a power pack to fire or excessive temperature.
Exposure to fire or temperature above 100°C (212°F) may cause explosion.
10. Have servicing performed by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the product
is maintained.
11. Switch o the power bank when not in use.
SAVE THESE INSTRUCTIONS
More information | Plus d'informations | Mehr Infos | Más información | Mais Informações | Maggiori informazioni |
更多信息 | 詳しくは | 추가 정보 |
πληροφορίε | Více informací | Meer informatie | Lisää tietoa | Több információ | Mer informasjon | Więcej informacji |
Mer information | ข้ อ มู ล มากกว่ า นี ้ | Thêm thông tin |
nativeunion.com/product-documentation
nativeunion.com/support
© 2020 Native Union all rights reserved. Native Union is a registered trademark of Design Pool Limited. Trademarks and trade
names are those of their respective owners. Copyright Design Pool Limited. 2/F, East Town Building, 41 Lockhart Road, Wan
Chai, Hong Kong. Made in China.
LED indication
Output: USB-A
Input / Output: USB-C
| | رثكا تامولعمDaha fazla bilgi | περισσότερε
अधिक जानकारी
|
Publicité
