ETI Solid State Lighting VersaStrip Guide D'utilisation Et D'entretien

USe and Care GUide
STriP LiGhT MOTiOn SenSOr
Package contents
Part Description Quantity
A Motion Sensor 1
nOTe: Motion sensor compatible with ETi product 54598142
nOTe: Keep your receipt and these instructions for proof of purchase.
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or
fluorescent tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
InstaLLatIon
1. Shut off power at the
electrical panel before
Knock out hole
beginning the installation.
2. Use a screw driver to
remove the bottom panel of
the motion sensor (A), and
punch out the knock out
hole on the bottom panel.
3. Feed the electrical wires
from the motion sensor
A
through the knock out
hole and install the bottom
A
panel back onto the motion
sensor.
B
4. Take your ETi strip light and remove the lens cover. Then unplug the wire connectors to disconnect the terminal.
5. Remove only one of the plastic covers. The motion sensor will replace the plastic cover.
6. Feed the wires from the motion sensor through the knock out holes in the fixture body and make the electrical
connections.
7. Snap the motion sensor to the fixture body. Slide the switch to the desired position to select a
hold-time of either 2 min, 5 min, or 15 min. Snap the lens cover back onto the fixture body.
8. Restore the power to the electrical box.
LED #1
LED #1
A
Driver #1
LED #2
A
care anD cLeanIng
Ordering # 90600647
Part # OS-ST-01
CaUTiOn: Before attempting to clean the light fixture, disconnect the power to the fixture by turning the breaker
off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals,
solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
troubLeshootIng
Minor problems often can be fixed without the help of an electrician.
WarninG: Before doing any work on the fixture, disconnect power to the light fixture.
Problem
A
The fixture will not light.
The fuse blows or the
circuit breaker trips when
the light is turned on.
WarninG: Carefully read and understand the information given in this manual before beginning the assembly
and installation. Failure to do so so could lead to electric shock, fire, or other injuries which could be hazardous or
even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the
Input Output
circuit breaker. • This product must be installed in accordance with the applicable installation codes by a person
familiar with the construction and operation of the product and the hazards involved. • Risk of electrical shock.
To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving
or cleaning. • Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical
systems. If not qualified, do not attempt installation. Contact a qualified electrician. • Risk of fire or electric shock.
Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs
and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire. •
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation. • To
prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
CaUTiOn: Not for emergency lighting.
WarninG: THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE
COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION. • Installers should not disconnect
existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers
should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder
lead wires by employing applicable connectors.
nOTiCe: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna,
increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit
different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV. Changes or
modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
WarrantY
This product is warranted for a period of 5 years from the date of original purchase against defects in materials and
LED #2
workmanship. If this product should fail to operate due to defects in material or workmanship within 60 months of
Driver #2 purchase, see www.ETiSSL.com for details. This product will be repaired or replaced, at ETi's option. This warranty is
expressly limited to repair or replacement of product and liability for direct, incidental, or consequential damages is
hereby expressly excluded. Some states do not allow exclusions of direct, incidental or consequential damages, so
the above limitation of exclusion may not apply to you. This warranty gives the consumer specific legal rights, which
vary from state to state. WARRANTY IS VOID IF PRODUCT IS NOT USED FOR THE PURPOSE WHICH THIS PRODUCT IS
MANUFACTURED.
Timer Switch
Possible cause solution
The power is off. Ensure the power supply is on.
The circuit breaker is off. Ensure the circuit breaker is in the on position.
There is a bad connection. Check to ensure proper wire connections are made. Contact
a qualified electrician.
There is a defective switch. Contact a qualified electrician.
The wires are crossed or the Check the wire connections. Contact a qualified electrician
power wire is grounding out. or call customer service 1-855-384-7754.
Questions, problems, missing parts?
Call ETiSSL Customer Service
8 a.m. - 5 p.m., CST, Monday - Friday
1-855-etI-ssLI (1-855-384-7754)
www.etissL.com
GUide d'UTiLiSaTiOn eT d'enTreTien
déTeCTeUr de MOUveMenT POUr réGLeTTe d'éCLairaGe
contenu De L'eMbaLLage
Pièce Désignation Quantité
A Détecteur de 1
mouvement
nOTe : Le détecteur de mouvement est compatible avec le produit ETi 54598142.
reMarQUe : Gardez votre facture ainsi que ces instructions comme preuves d'achat.
averTiSSeMenT : Coupez le courant au panneau de disjoncteurs ou de fusibles avant d'enlever le vieux
luminaire, le ballast ou les tubes fluorescents.
Si vous n'êtes pas familiers avec les installations électriques, nous vous recommandons de faire ppel à un électricien
qualifié pour l'installation.
InstaLLatIon
1. Coupez le courant au
panneau électrique avant
Trous à pastille
de faire l'installation.
2. À l'aide d'un tournevis,
enlevez le couvercle du
détecteur de mouvement
(A) puis défoncez la
débouchure du couvercle.
3. Passez les fils électriques
du détecteur de mouvement
A
dans la débouchure et
remettez le couvercle sur le
A
détecteur de mouvement.
B
4. Saisissez la réglette ETi et enlevez le diffuseur. Débranchez les connecteurs au bornier.
5. Enlevez l'un des couvercles en plastique Il sera remplacé par le détecteur de mouvement.
6. Passez les fils du détecteur de mouvement dans les débouchures du corps de la lampe et effectuez les connexions
électriques.
7. Enclenchez le détecteur de mouvement sur le corps de la lampe. Glissez le commutateur à la position voulue pour
sélectionner la durée : 2 min., 5 min, ou 15 min. Réenclenchez le diffuseur sur le corps de la lampe.
8. Remettez le circuit sous tension.
DEL n° 1
DEL n° 1
A
Transfo n° 1
DEL n° 2
A
n° de commande 90600647
n° de pièce OS-ST-01
A
Entrée Sortie
DEL n° 2
Transfo n° 2
Commutateur de minuterie