Publicité
Liens rapides
AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
31-5270
31-5275
ITEM
QTY
1
1
BULL BAR ASSEMBLY
2,3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
PLASTIC PLUG
5
4
RUBBER BUMPER
6
6
BOLT PLATE
7
6
M12 FLAT WASHER
8
6
M12 LOCK WASHER
9
6
M12 HEX NUT
10
4
M10 HEX HEAD BOLT, STAINLESS STEEL
11
8
M10 FLAT WASHER, STAINLESS STEEL
12
4
M10 LOCK WASHER, STAINLESS STEEL
13
4
M10 HEX NUT, STAINLESS STEEL
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
PIEZA DE SUJECIÓN, LADO DEL ACOMPAÑANTE
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
6
PLACAS DE PERNOS
7
6
ARANDELA PLANA SAE DE M12
8
6
ARANDELAS DE PRESIÓN DE M12
9
6
TUERCAS HEXAGONALES DE M12
10
4
PERNOS CON CABEZA HEXAGONAL DE M10 ACERO INOXIDABLE
11
8
ARANDELAS PLANAS DE M10 ACERO INOXIDABLE
12
4
ARANDELAS DE PRESIÓN DE M10, ACERO INOXIDABLE
13
4
TUERCAS HEXAGONALES DE M10 ACERO INOXIDABLE
1
1
LA BULL BAR
2,3
2
SUPPORT CÔTÉ PASSAGER (2) ET CÔTÉ CONDUCTEUR (3)
4
2
BOUCHON DE PLASTIQUE
5
4
PARE-CHOCS EN CAOUTCHOUC
6
6
PLAQUES DE BOULON
7
6
RONDELLE PLATE SAE M12 PO
8
6
RONDELLE A FREIN M12 PO
9
6
ÉCROU HEXAGONALM12
10
4
PERNOS CON CABEZA HEXAGONAL DE M10
11
8
RONDELLE PLATE SAE M10PO
12
4
RONDELLE A FREIN M10 PO, ACIER INOXYDABLE
13
4
ÉCROU HEXAGONAL M10, ACIER INOXYDABLE
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely
before beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners.
STEP 2.
NOTE: It may be necessary to remove the front license plate and bracket. Remove license plate from bracket. Using a
3/16" drill bit, drill out the two pop rivets that hold the bracket to the bumper. If local/state laws requires a license
plate, license plate relocation kit 32-0055 is available.
STEP 3.
Remove tow hooks by removing the front bolt and rear bolt that threads into the side of the tow hooks. Tow hooks
will not be reinstalled.
STEP 4.
Determine passenger and driver side brackets. Slide bracket in through the tow hook pocket. Align slots on bracket
with holes on frame. Slide the three bolt plates inside the frame and out through aligned holes on both sides of the
frame. Secure with M12 yellow zinc fasteners. Leave loose. SEE FIGURE 2.
NOTE: Minor trimming of tow hook area may be needed. It may be necessary to clean out mounting holes on frame.
SEE FIGURE 2.
STEP 5.
Attach Bull Bar to mount brackets using M10 stainless steel fasteners. Level and adjust Bull Bar as desired and tighten
all fasteners. Recommended torque values are 25-30. Lbs. for M12 yellow zinc fasteners and 15-20. Lbs. for M10
75-0984-RevB
All manuals and user guides at all-guides.com
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-2013 CHEVY SILVERADO/ GMC SIERRA 1500 SERIES
APLICACIÓN: CHEVY SILVERADO MC SIERRA 1500, 2007-13
APPLICATION: CHEVY SILVERADO/GMC SIERRA 1500, 2007-13
1
CONTENTS -
CONTENIDO
, ACIER INOXYDABLE
W16-0010
- CONTENU
(2)
Y EL CONDUCTOR
ACIER INOXYDABLE
/G
2
3
TOOLS -
HERRAMIENTA
16MM SOCKET
16MM WRENCH
18MM SOCKET
18MM WRENCH
RATCHET
SOCKET EXTENSION
TORQUE WRENCH
UTILITY KNIFE
DADO DE 16MM
(3)
LLAVE DE TUERCAS DE 16MM
DADO DE 18MM
LLAVE DE TUERCAS DE 18MM
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
NAVAJA
CLE 16MM PO
DOUILLE 16MM PO
CLE 18MM PO
DOUILLE 18MM PO
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
COUTEAU
6
- OUTILS
2/9/2016
Publicité
Sommaire des Matières pour Westin 1500 Serie
- Page 1 STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners. STEP 2.
- Page 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Page 3 INSTALACIÓN DE LA PLACA DE PERNOS MONTAGE DE LA PLAQUETTE DE BOULON FIGURE 2 FIGURA 2 FIGURA 2 Thank You for choosing Westin products Westin Automotive Products, Inc. For additional installation assistance please call 5200 N. Irwindale Ave. Suite 220 Irwindale, Ca. 91706...